iron_fruitman
最新回复 发布由 iron_fruitman
-
-
-
The issue is : the RSBN coded in the Mig are nowhere consistent with the map.
Some are irrelevant in the context of the map (cold war, east vs west) like Rammstein or Brement airfields (don't get me wrong : it is nice to have more airfields covered but not if the other ones aren't) and some are just "not like indicated on the map" (Wittstock is 14 in the Mig but 22 on the map).
In addition, only 19 out of 40+ potential airfields are covered...
This is wrong at every level.
-
1
-
1
-
-
@skywalker22 Hello !
Big thanks for your work !
I point I noted : I have downloaded your latest release of the "R_NAV_data_GermanyCW.lua" and I cannot make it work (it crashes myu DCS). Going back to the previous one solves the issue.
It may be linked to the name of the file : the new one is "R_NAV_data_GermanyColdWar.lua" instead of "R_NAV_data_GermanyCW.lua".
Game is pretty unmodded (A-4E only).
DCS discord log analyzer points towards a cockpit issue.
Thanks.
-
Quote
That is unfortunately a result of DCS's internal runway handling and the reason that I had to add the ungainly 'left^' and 'right' attributes to a TDZ. You may have to experiment with them and create two TDZ for the same RWY, one left and one right. One of them will be 'wrong' (inverted).
My apologie for being unclear : my point is that the arguments starts and extend seem to be inverted in DML.
According to the documentation (sorry for quoting you ^^) :
- extend : Extend the length of the runway (as reported internally by the map’s DB) by this amount of meters.
- starts : Offset (in meters) from the runway threshold (as defined by DCS’s airfield DB) where the TDZ starts
While in my test, when I fill the "starts" argument with a positive value (360 in the exemple above), it shrinks the zone size by 360m.
The extend arg offsets the position of the zone.
Knowing that, I was able to create the mission but I think either the documentation or the module has it inverted
Thank you.
-
@cfrag Sorry to bother you again.
Another small-non-blocking issue : the starts / extend parameters are inverted (may also be the case for the expand and stops ; I have not tested them) :
- starts reduces / increases the length of the runway
- extend moves the runway
In addition, negative values seem to increase (or move up) the zone (for the respective parameters) instead of reducing / moving down the zone.
I have attached a few screenshots, both in the ME and in game.
-
@cfrag works like a charm, thank you !
-
Hello cfrag,
first of all, thank you for your work !
I am trying to set up a TDZ training mission and I encounter the attached issue when "touching" the runway and again when coming to a full stop (same error message).
First time using this module so it may be a bad setup from my side.
I joined the .miz as well as the logs.
Thank you again !
EDIT : in the miz, the plane is Blue and the airfield is Red. Tried Red on Red but same issue.
BetAB-500shp exploding mid flight
在 Weapon Bugs
发布于 · 本帖最后于，由iron_fruitman编辑
Better Tacview image
Hello,
The betAB-500shp are detonating mid flight (most likely when the booster activates).
The attached miz is a simple mission on Caucasus to reproduce it. The track is me droping the bomb and seing them detonate too early.
When not setting the Bomb Arming switch, the parachute does not open, the booster goes ON and the bomb impacts the ground properly (and then does not detonate, which is ok).
Not in this track : release from higher altitude; release at 500kph and release at higher speed. Issue reproduced in all these configurations.
Tacview snapshot to show the bomb exploding mid flight (around 24m AGL).
Thank you.
Configuration :
- DCS v22.9.21.16552 MT
- Update from previous version (no idea if this was working in the previous patch)
- Slow repair performed
- Mod: A-4E-C
LastMissionTrack.trk Caucasus - Betab 500shp test.miz