trace
-
Posts
43 -
Joined
-
Last visited
Recent Profile Visitors
1778 profile views
-
Unfortunate I do not print them anymore. The print isnt that easy and had lots of unuseable prints to dump. Also it was all in our hobby time with no interest on profit. Can`t also provide STLs. If things are changing we gonna publish it here. THX trace
-
@dburne if I would have known that you will need some stuff from Milan I could have organized it to keep total shipping cost low, like I did before for someone else. @crazysundog made a "nightshift" your F-16 pedals are printed.
-
Hya Crazysundog, did not forget you I am printing them in my spare time. Best regards trace
-
Hello dburne, sounds fantastic and looking forward for your intensive flying experience on Saturday. Hope you will find your own comfortable postion with your new setup. Best regards trace
-
We are not heading for any profit and doing them when we can and only on Pilots demand and happy you are liking it.
-
woohay its minesold
-
Also a nice option to get them lifted. You will make it.
-
@Revvin the maximum width including the F-16 pedals is 53.5cm The P1-X Cockpit has a max width between the 40x160mm Profile of 500mm I see whatever you do it wont be easy in the standard configuration with any pedals. The MFGCrosswind would fit in width 494mm in orginal Version but mind the original pedals have a max. height of 264mm. My advice, if you need more width in the cockpit, you replace the Item profiles out of the part list and you will gain more than 80mm width: https://shop.gperformance.eu/wp-content/uploads/2020/07/P1-X-manual-0-9.pdf You will need to replace following positions: A2: 40x160L Slot8 (length 580mm plus 2x thickness of pos. B26) C9: 40x160L Slot8 (length 550mm plus 2x thickness of pos.B26) C10: 40x80L Slot8 (length 550mm plus 2x thickness of pos.B26) Then you install the Monitor mount with vertical Profile and plate B26 to the inside. Please cross check parameters. In the UK where you live is Moteddis one ressource to get these profiles. https://www.motedis.co.uk/shop/index.php I hope this helps you for your cockpit PX-1 plan to get more width and you can think about if this would be a solution. I wrote already the manufacture to get the exact thickness of B26 for you. best regards trace
-
Hy Revinn, you mean the F-16 Pedals on the MFG? Nice setup you are using. This cockpit gives lots of freedom using gear.
-
Hello Goblin / JT, I have seen your vid and I want to say you have made an amazing job with this concept, where nowadays space is expensive. Are you still using this setup?
-
Where you are based? Best regards trace
-
Hello Chaos, thank you very much for the nice pictures and your positive review. As you already mentioned it due to the support structure the roughness on the backside is unavoidable. Thanks again and if you have any further questions or constructable feedback send me a PM or post it. Best regards trace
-
@BIG10 at the moment I am hard at work, so I havent got the time to do some other things. I print those in my spare time and its not my major Job and non profit. We want to bring our hobby with rigid long lasting addons further ahead. Therefore we spend lots of time developing, testing and printing. So I ask you for patience for the pictures you are requesting. Thank you and Best regards trace
-
NOW I finished the needed left side pedals to get the pair ready to rumble.......
-
Good morning Sydy, thanks a lot. Beeing honest we had hard nights to get to this point, but it was it worth. Nice to read you like it. Thanks again. If we do following prints for interested guys we still need to keep in mind the print time of 44hrs per pair and further manual Processing to achieve the outstanding rigidity and keeping the shown quality. We use a special filament which is not easy to use, but gives a nice metal like finish. Think it won't be that much. just to cover the print. Best regards trace Nice city and Aircraft in your profile
