Jump to content

Frage zur Mirage


Ulfr85

Recommended Posts

Hey, und zwar versuche ich vergeblich bei der Magic in den CCM zu kommen, "V" taste funktioniert nicht.

Ich suche nun in den Steuerungsoptionen aber finde da keine Aktion die es sein könnte, bin ich einfach nur blind oder unfähig? :-(

 

 

 

Gruß

Guido

F/A-18C, AV-8B, Huey, Ka-50, Mig-21, A10C, FC3, BF-109, M2000C, AJS-37, P-51

 

Ryzen 5 2600 ~4Ghz, 16GB DDR4 3200Mhz, EVGA GTX 1070

Link to comment
Share on other sites

Versuch mal Special Mode FWD und Special Mode AFT,

da gibt es keine Keyboardbelegung.

 

Gruss Steph

"You want me to fly in the back of a tiny little jet with a crazy fighter pilot who thinks he´s invincible,

home in on a SAM site in North Vietnam and shoot it before it shoots me?

You´ve gotta be shittin´me!"

 

Captain Jack Donovan

Link to comment
Share on other sites

Mach das,

 

für den Anfang auch sehr zu empfehlen

 

https://drive.google.com/file/d/0B-uSpZROuEd3WnVhcm5hTUJOTjg/view

"You want me to fly in the back of a tiny little jet with a crazy fighter pilot who thinks he´s invincible,

home in on a SAM site in North Vietnam and shoot it before it shoots me?

You´ve gotta be shittin´me!"

 

Captain Jack Donovan

Link to comment
Share on other sites

Hi,

 

im Handbuch von Razbam steht fogendes:

 

The (DÉCOLLAGE/TAKE-OFF CONFIG) warning light turns on if:

 

 The cover for the FBW test switch is open. :thumbup:

 The FBW test warning light is red. :thumbup:

 The aircraft is not trimmed for take-off :helpsmilie:

 Emergency trim is selected. :music_whistling:

 BECS switch is not in the AUTO position. :thumbup:

 ANEMO switch is in the OFF position :thumbup:

 

:helpsmilie:wo kann ich den Knopf für das Trimmen T/O finden bzw. was muss man machen, damit das Trimmen richtig eingestellt ist ...

 

Frage deshalb, weil beim Startup immer die rote "DECOL" Lampe leuchtet und ich keine Ahnung habe, was ich falsch mache ...

 

Achso, wenn ich am Emergency Trim rumgefummelt habe ... wie bekomme ich den wieder ausgeschaltet ?


Edited by caponi

too much ...

 

 

Link to comment
Share on other sites

Die mirage muss nicht getrimmt werden. Weil flybywire ? Gruss

System

 

Hydro H115i with 8700k @ 4,9 ghz all cores, Asus strix Z370 f, 32gb ddr4 3600Mhz, Asusrog swift 34 gsync ,Vr hp Reverb .Palit gaming pro 2080 ti Thrustmaster Warthog f18grip and th pedal

Steamvr ss 100% and dcs world ss 180%

 

tomcat eats the viper for breakfast :P

Lange lebe die Tomcat": Long live the Cat!

Link to comment
Share on other sites

Du kannst das Flugzeug wieder neutral trimmen, indem du einfach den Autopilot Master kurz auf Standby schaltest (gelbes Licht). Falls Trimmung der Grund für die Decol-Warnung war, sollte sie damit verschwinden. Beim Startup kannst du die Trimmung jedoch komplett ignorieren, das macht das Flugzeug von alleine. Warnung kommt nur, wenn es manuell aus der Neutral (Takeoff) Position herausgetrimmt wurde.

Meistens ist die Ursache für das Warnlicht allerdings ein nicht oder falsch durchgeführter FBW-Test. Da bist du dir sicher, dass alles passt? ;)

- Cover auf

- Schalter umlegen

- aufs grüne Licht warten

- Schalter zurück

- Cover zu

 

Die mirage muss nicht getrimmt werden. Weil flybywire ? Gruss

Nicht (immer) ganz richtig. FBW kompensiert z.B. nicht asymetrische Ladungsverteilung...


Edited by spiddx

Specs:

 

 

i9 10900K @ 5.1 GHz, EVGA GTX 1080Ti, MSI Z490 MEG Godlike, 32GB DDR4 @ 3600, Win 10, Samsung S34E790C, Vive, TIR5, 10cm extended Warthog on WarBRD, Crosswinds

 

Link to comment
Share on other sites

also FBW-Test bin ich mir sicher ...

 

aber ich bin mir nicht sicher, ob ich den Trimmer am Stick berührt habe oder nicht.

AP testen setzt auf Neutral ?

Hmmm ... das habe ich bis jetzt noch gar nicht gelesen ... mal ausprobieren :)

too much ...

 

 

Link to comment
Share on other sites

AP testen setzt auf Neutral ?

 

Nein, nicht AP Test, sondern AP Master Mode. Siehe Anhang.

Screen_170112_141209.thumb.jpg.6d32349ca565f0fd95524dc2bfd43735.jpg

Specs:

 

 

i9 10900K @ 5.1 GHz, EVGA GTX 1080Ti, MSI Z490 MEG Godlike, 32GB DDR4 @ 3600, Win 10, Samsung S34E790C, Vive, TIR5, 10cm extended Warthog on WarBRD, Crosswinds

 

Link to comment
Share on other sites

Bei mir blieb das DECOL Warnlicht auch immer als letztes aktiv. Wusste mir auch keine Rat, bis ich dann mal das Cold Start Training gemacht habe. Seit dem keine Probleme mehr.

 

Da habe ich gleich gesehen, was ich alles so falsch gemacht habe... :megalol:

AMD Ryzen 7 5800X | 32GB DDR4 RAM | NVidia RTX4080 | MSI B550 TOMAHAWK | Creative X-Fi Titanium | Win 10 Pro 64bit | Track IR4 Pro | Thrustmaster Warthog | Saitek Rudder Pedals

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...