assafm25 Posted January 14, 2017 Share Posted January 14, 2017 I have Microsoft FF 2 with FF . all the time i tray to use the built in FF option on DCS i lose my Trim On the Heli. its not feel like its work at all. any one make it work ? [sIGPIC][/sIGPIC] IAF Bell205 IAF Anafa ----------------------- DCS World Modules: A-10C, FC3, MiG-21BiS, F-86, P-51, KA-50, UH-1H Huey, Mi-8, M2000K, Gazal, Bf109, Mig-15, Hawk and NTTR ----------------------- My System - ASUS Maximus HERO iiiv, CoolMaster 120 Sadion Plus, I7 -6700K @4.0, G.Skill ddr4 16GB ram, Gigabyte GTX 1070 G1 , PSU Seasonic X-650W, OCZ 150 500Gb ssd drive X2, Seagate 7200 1T X2. ------------- Link to comment Share on other sites More sharing options...
20thBG_Blackwolf Posted January 15, 2017 Share Posted January 15, 2017 Do you have the trim set to FFB joy with no spring in the special section on set up? BSD Discord , BSD Website If it doesn't hover, it just sucks and blows Link to comment Share on other sites More sharing options...
assafm25 Posted January 15, 2017 Author Share Posted January 15, 2017 (edited) Curv and dead zone in all axess on zero. Also no invert or some check box selection on the axis tone. Btw Way i cant just use curv on collective (diffrent stick) and enjoy the trim. This behavior start only after i check the FF box on DCS. If i use3 party software for the FF (i found a old tool that one of the member made for the ka50) Its work ok but i note recive fedback from the sim to the FF sensor. Edited January 15, 2017 by assafm25 [sIGPIC][/sIGPIC] IAF Bell205 IAF Anafa ----------------------- DCS World Modules: A-10C, FC3, MiG-21BiS, F-86, P-51, KA-50, UH-1H Huey, Mi-8, M2000K, Gazal, Bf109, Mig-15, Hawk and NTTR ----------------------- My System - ASUS Maximus HERO iiiv, CoolMaster 120 Sadion Plus, I7 -6700K @4.0, G.Skill ddr4 16GB ram, Gigabyte GTX 1070 G1 , PSU Seasonic X-650W, OCZ 150 500Gb ssd drive X2, Seagate 7200 1T X2. ------------- Link to comment Share on other sites More sharing options...
assafm25 Posted January 15, 2017 Author Share Posted January 15, 2017 Looks Like the problem solved after marking the "Swap Axis" Checkbox [sIGPIC][/sIGPIC] IAF Bell205 IAF Anafa ----------------------- DCS World Modules: A-10C, FC3, MiG-21BiS, F-86, P-51, KA-50, UH-1H Huey, Mi-8, M2000K, Gazal, Bf109, Mig-15, Hawk and NTTR ----------------------- My System - ASUS Maximus HERO iiiv, CoolMaster 120 Sadion Plus, I7 -6700K @4.0, G.Skill ddr4 16GB ram, Gigabyte GTX 1070 G1 , PSU Seasonic X-650W, OCZ 150 500Gb ssd drive X2, Seagate 7200 1T X2. ------------- Link to comment Share on other sites More sharing options...
Recommended Posts