Jump to content

When I install the fuel tank , centerline, AJS-37 is totally untrimable


Ramstein

Recommended Posts

When I install the fuel tank , centerline, AJS-37 is totally untrimable. The plane just goes totally out of control... it will not fly straight and is out of control.

 

What happened? :helpsmilie:

 

:joystick:

ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind

G.Skill 64 GB Ram, 2TB SSD

EVGA Nvidia RTX 2080-TI

55" Sony OLED TV, Oculus VR

 

Link to comment
Share on other sites

When I install the fuel tank , centerline, AJS-37 is totally untrimable. The plane just goes totally out of control... it will not fly straight and is out of control.

 

What happened? :helpsmilie:

 

:joystick:

 

Give us more infos or give us a track

 

Like speed?

Link to comment
Share on other sites

not much to see... it just goes out of control and crashes.... or you get lucky and spin around and upside down a few more seconds before crashing..

ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind

G.Skill 64 GB Ram, 2TB SSD

EVGA Nvidia RTX 2080-TI

55" Sony OLED TV, Oculus VR

 

Link to comment
Share on other sites

Track of trim gone bad.

It is possible the Saitek stick is sending bad inputs.

I try cancelling out trim with the O key, in the control panel it says use that key to cancel trim.

 

I used an instant mission, it cut the time and get to the issue without a full mission with takeoff...

as you can see it happen well after the start... I don't have problems until I try to add any type of trim. Then go back to no trim to cancel out and go back to neutral. Also, I try setting the Autopilot button on top left cockpit to see if that will take over and smooth out the ride. But it just turns those off as it gets worse until it is totally out of control. It starts going bad quickly while flying. :joystick:

DCS_Viggen_Track_Trim_Gone_Bad.zip

ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind

G.Skill 64 GB Ram, 2TB SSD

EVGA Nvidia RTX 2080-TI

55" Sony OLED TV, Oculus VR

 

Link to comment
Share on other sites

I did add a flat spot on the rudder, so there is no input of any kind for about 10% of the middle for the rudder.. I think I was getting erroneous inputs causing the rudder to move around..

ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind

G.Skill 64 GB Ram, 2TB SSD

EVGA Nvidia RTX 2080-TI

55" Sony OLED TV, Oculus VR

 

Link to comment
Share on other sites

  • 7 months later...

AJS Viggen Trim not works

 

Hi,

the same Problem here both Joystick and Keyboard keys don´t work. I can´t trim teh Viggen. Other Moduls like F-5E and SU-25 works correctly with teh Input by teh Joystick.

 

AMD Graphic Cards Radeon HD 7800

Intel i-7 3.40 GHZ

G.Skill DDR3 ram 16 GB

46" Samsung LCD HDTV

Win10 pro x64

Thrustmaster T16000, TWS Throttle, Thrustmaster Pedals

Link to comment
Share on other sites

Ramstein, so you are talking about the rudder trim (yaw) and not the pitch trim? Quite an important ‚detail‘ since there are different trimming systems.

 

I‘m using the external tank on almost every flight and never had any such issues. I‘m using TM Warthog and version 1.5.7 most of the time.

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...