Shimmergloom667 Posted February 13, 2020 Share Posted February 13, 2020 So, I got my T50CM2 throttle the other day, and while it is a pretty damn great piece of hardware, I wish the two encoders on the grip were actual axis - since encoders in DCS are really limited, are they? What do YOU guys user your encoders for? i7 - 9700K | 32 GB DDR4 3200 | RTX 2080 | VKB Gunfighter Mk II /w MCG Pro | Virpil T-50CM2 Throttle | TrackIR 5 | VKB Mk. IV AJS-37 | A/V-8B | A-10C | F-14A/B | F-16C | F-18C | F-86F | FC3 | JF-17 | Ka-50 | L-39 | Mi-8 | MiG-15bis | MiG-19 | MiG-21bis | M2000-C | P-51D | Spitfire LF Mk. IX | UH-1H Link to comment Share on other sites More sharing options...
Sabre_Ewan Posted February 13, 2020 Share Posted February 13, 2020 I don't have any encoders on my controls yet, but if I did I'd use them for radio controls, lights, course knob, RWR volume in the F18. I've never messed with any of that kind of thing, but surely it would also be possible to set them up to work as an axis. So an 'up' turn increases a virtual axis and a 'down' decreases it. Link to comment Share on other sites More sharing options...
Astronaut Posted February 13, 2020 Share Posted February 13, 2020 So, I got my T50CM2 throttle the other day, and while it is a pretty damn great piece of hardware, I wish the two encoders on the grip were actual axis - since encoders in DCS are really limited, are they? What do YOU guys user your encoders for? Encoder on the right of throttle handle is my radar ant elevation control, on the left is my manual range knob (f-16, haven't used it for anything in the hornet yet) Two encoders on the base are for my heading and course knobs/switches. Found encoders to be more useful to me, I set up the flaps lever to be a 3 position switch for flaps instead of an axis and the ring finger slider axis is just a zoom. 12900K | MSI Z690 | STRIX RTX3090 | 64GB DDR4 3600MHz | NVMe Storage gen3 | Custom Loop | Valve Index Link to comment Share on other sites More sharing options...
mazex Posted February 16, 2020 Share Posted February 16, 2020 An important note is to change them to buffered - that works a lot better for DCS, at least for me... See page 9 in the "community manual" for the configuration software I started to write: https://sites.google.com/site/mazexx...edirects=0&d=1 More in this post: https://forums.eagle.ru/showthread.php?t=242447 Ryzen 7800X3D | Gigabyte X670 Aorus Elite AX MB | 32GB 6000Mhz DDR5 | RTX 3080 GPU | Sound BlasterX AE-5 | Windows 11 Pro x64 | Virpil T-50 Throttle | T50 CM2 Grip + WarBRD | VKB T-rudder MK IV | Asus PG279Q 1440p | Valve Index VR | Samsung 980 Pro as system disk and DCS on separate Intel 665P NVME SSD Link to comment Share on other sites More sharing options...
driftaholic Posted February 18, 2020 Share Posted February 18, 2020 I think you can also create a virtual axis from the encoders. https://forum.virpil.com/index.php?/topic/850-setting-delta-encoder-wheel-as-virtual-axis-and-hardcoded-axis-precision/ Link to comment Share on other sites More sharing options...
Alligin Posted March 11, 2020 Share Posted March 11, 2020 An important note is to change them to buffered - that works a lot better for DCS, at least for me... See page 9 in the "community manual" for the configuration software I started to write: https://sites.google.com/site/mazexx...edirects=0&d=1 More in this post: https://forums.eagle.ru/showthread.php?t=242447 Thanks Mazex, I’ll have a look over that later. Link to comment Share on other sites More sharing options...
Alligin Posted March 11, 2020 Share Posted March 11, 2020 Encoder on the right of throttle handle is my radar ant elevation control, on the left is my manual range knob (f-16, haven't used it for anything in the hornet yet) Two encoders on the base are for my heading and course knobs/switches. Found encoders to be more useful to me, I set up the flaps lever to be a 3 position switch for flaps instead of an axis and the ring finger slider axis is just a zoom. Astronaut How do you change the flap lever from an axis to a 3 position switch? I too would like to use it as flaps. Link to comment Share on other sites More sharing options...
HC_Official Posted March 11, 2020 Share Posted March 11, 2020 Astronaut How do you change the flap lever from an axis to a 3 position switch? I too would like to use it as flaps. you use axis to button configuration, see the tutorial links in my signature No more pre-orders Click here for tutorials for using Virpil Hardware and Software Click here for Virpil Flight equipment dimensions and pictures. . Link to comment Share on other sites More sharing options...
RackMonkey Posted May 10, 2020 Share Posted May 10, 2020 Slow encoder rotation Encoder on the right of throttle handle is my radar ant elevation control, on the left is my manual range knob (f-16, haven't used it for anything in the hornet yet) Two encoders on the base are for my heading and course knobs/switches. Found encoders to be more useful to me, I set up the flaps lever to be a 3 position switch for flaps instead of an axis and the ring finger slider axis is just a zoom. Astronaut Have you found a way to speed up the rotation of the encoders on you heading and course bugs? Normal encoder rotation is way to slow, using buffering and I end up way past where I want to set them. I have no idea what scroll means, I can't see any difference. If I could, I would assign the push button on the encoder as a shift causing the rotation to move the bug 5 degrees at a time and leave the normal position at 1 degree at a time. As of yet I cant find a way to change the rate at which the encoder changed the bug's. I haven't looked at Joystick Gremlin yet, may it has the functionality to do what I want. MSI Z490 Tomahawk, I5-11600kf, 2X512GB NvME, RTX4090, 32GB DDR4 3200, Reverb G2, T50-CM2, OpenXR 31st TFW, 14th MAS, 9th ARS Link to comment Share on other sites More sharing options...
Shiny Posted May 12, 2020 Share Posted May 12, 2020 I use mine as follows: - Left side encoder - TGP zoom in/out, push in for FoV/RAID. Also doubles for antenna elevation in something like the hornet. In the Harrier, I use it for the nozzle STO stop lever. In the Spitfire, it's my RPM lever. - Right side encoder - Could also be used for antenna elevation for the hornet. In my A10C, dial up to choose jammer mode, dial down to enable/disable jammer. The reason I do this is that the 5 way hat switch right there I also use as the CMS so all my countermeasures are right under my thumb on my A10C. - E1 encoder, push to activate NVG, rotate knob left and right for brightness - E2 encoder, I have mapped to Joystick Gremlin. When I'm in mode 2 or mode 3, (these are my approach/takeoff and ground startup mode) the push is for bringing up kneeboard and the dial flips pages for the kneeboard. - E2 encoder in mode 1, which is my combat mode, I use it for HMD brightness for the Viper and the Hornet. Link to comment Share on other sites More sharing options...
Skwirl865 Posted September 8, 2021 Share Posted September 8, 2021 On 3/11/2020 at 7:54 AM, HC_Official said: you use axis to button configuration, see the tutorial links in my signature Does it show up as an axis in dcs? Link to comment Share on other sites More sharing options...
HC_Official Posted September 8, 2021 Share Posted September 8, 2021 (edited) the axis will still be active if thats what you are asking Edited September 8, 2021 by HC_Official No more pre-orders Click here for tutorials for using Virpil Hardware and Software Click here for Virpil Flight equipment dimensions and pictures. . Link to comment Share on other sites More sharing options...
Skwirl865 Posted September 9, 2021 Share Posted September 9, 2021 15 hours ago, HC_Official said: the axis will still be active if thats what you are asking I mean if u create a virtual axis in the virpil software and u open dcs, will u bind it in the “axis commands” section of dcs controls or in the regular keybinds section. Will it still show up as button presses or like a real axis in dcs Link to comment Share on other sites More sharing options...
Sabre_Ewan Posted September 9, 2021 Share Posted September 9, 2021 9 minutes ago, Skwirl865 said: I mean if u create a virtual axis in the virpil software and u open dcs, will u bind it in the “axis commands” section of dcs controls or in the regular keybinds section. Will it still show up as button presses or like a real axis in dcs If you set up a virtual axis, you'll bind it in the axis section in DCS. Link to comment Share on other sites More sharing options...
HC_Official Posted September 9, 2021 Share Posted September 9, 2021 (edited) dunno what you guys are going on about, I said axis to button bindings when replying to Alligin you break your axis into 3 button ranges, so your lever can control 3 flaps settings by generating button presses when within these ranges Edited September 9, 2021 by HC_Official 1 No more pre-orders Click here for tutorials for using Virpil Hardware and Software Click here for Virpil Flight equipment dimensions and pictures. . Link to comment Share on other sites More sharing options...
dburne Posted September 9, 2021 Share Posted September 9, 2021 4 minutes ago, HC_Official said: dunno what you guys are going on about, I said axis to button bindings when replying to Alligin you break your axis into 3 button ranges, so your lever can control 3 flaps settings by generating button presses when within these ranges This - absolutely works a charm. 1 Don B EVGA Z390 Dark MB | i9 9900k CPU @ 5.1 GHz | Gigabyte 4090 OC | 64 GB Corsair Vengeance 3200 MHz CL16 | Corsair H150i Pro Cooler |Virpil CM3 Stick w/ Alpha Prime Grip 200mm ext| Virpil CM3 Throttle | VPC Rotor TCS Base w/ Alpha-L Grip| Point Control V2|Varjo Aero| Link to comment Share on other sites More sharing options...
Skwirl865 Posted September 9, 2021 Share Posted September 9, 2021 17 minutes ago, HC_Official said: dunno what you guys are going on about, I said axis to button bindings when replying to Alligin you break your axis into 3 button ranges, so your lever can control 3 flaps settings by generating button presses when within these ranges I did that with the “lever” axis. Not 3 but 2. I did between gear up at 100%, 60-80% is flaps up, flaps down between 20-40% and gear down at 0%. you’re right about it working like a charm. I love this thing and I haven’t had it but 3 days lol. I misread what u were saying. I have my encoders set the same way but to different functions but the same for hmcs in the hornet and f-16. I think I might steal your kneeboard encoder binding. I may actually switch my countermeasures to where yours is too now that I think about it. It makes more sense than the thumb hat on the stick Link to comment Share on other sites More sharing options...
Sabre_Ewan Posted September 12, 2021 Share Posted September 12, 2021 Sorry, I also missed a couple of posts and then assumed you were talking about the original topic. 1 Link to comment Share on other sites More sharing options...
Skwirl865 Posted September 12, 2021 Share Posted September 12, 2021 I was just wondering if a virtual axis really showed up as a new axis in the axis commands section of dcs. That sounds interesting. Link to comment Share on other sites More sharing options...
skypickle Posted January 7, 2022 Share Posted January 7, 2022 anybody figure out how to speed up the encoder dials? I need to turn them A LOT to get a gauge in DCS to reflect the input. 4930K @ 4.5, 32g ram, TitanPascal Link to comment Share on other sites More sharing options...
HC_Official Posted January 8, 2022 Share Posted January 8, 2022 5 hours ago, skypickle said: anybody figure out how to speed up the encoder dials? I need to turn them A LOT to get a gauge in DCS to reflect the input. Yeah I use joystick gremlin to handle that No more pre-orders Click here for tutorials for using Virpil Hardware and Software Click here for Virpil Flight equipment dimensions and pictures. . Link to comment Share on other sites More sharing options...
skypickle Posted January 8, 2022 Share Posted January 8, 2022 @HC_Official so I installed vJoy and Joystick gremlin. WHOA. Brain slammed. All I want to do is send 10 keypresses for a single click on the encoder. Is there a good video I can watch that you know of? I do not want to remap all my other bindings. 4930K @ 4.5, 32g ram, TitanPascal Link to comment Share on other sites More sharing options...
skypickle Posted January 9, 2022 Share Posted January 9, 2022 Finally figured it out. It is still suboptimal. Even though I have programmed a macro to hit the 'zoom out' keypress 10x, it is agonizingly slow and not responsive. 4930K @ 4.5, 32g ram, TitanPascal Link to comment Share on other sites More sharing options...
HC_Official Posted January 9, 2022 Share Posted January 9, 2022 for a zoom function , if you dont have an analog axis for it but have 3 buttons spare maybe use button to axis config to do this (this is what I use for zoom on my virpil ALpha-L that is on my collective) No more pre-orders Click here for tutorials for using Virpil Hardware and Software Click here for Virpil Flight equipment dimensions and pictures. . Link to comment Share on other sites More sharing options...
Recommended Posts