emc Posted September 8, 2020 Share Posted September 8, 2020 Did you see any performance (FPS) increase? I didn't make any test, I do it just for 'my-personal-perfectionist' sake Take a look my mods CPU: i7 7700 | GPU: GeForce GTX 1080 8GB DDR5 | Motherboard: ASUSTeK PRIME B250M-A | RAM: 2x16GB DDR4-2400 | Output: Kingston HyperX Cloud II | Edifier C2XD 2.1 | Controlls: Saitek X-56 Rhino | Saitek Flight Rudder Pedals | Saitek Multi/Radio/Switch Panels | Thrustmaster MFD Cougar | Elgato Stream Deck XL | OpenTrack with LaserClip | VoiceAttack with VAICOM Pro plugin Link to comment Share on other sites More sharing options...
streakeagle Posted September 9, 2020 Share Posted September 9, 2020 I dunno if you saw this, but Cubesim is developing real-life sized F/A-18 DDI and AMPCD (5x5 inches, 720x720 IPS panel) as well corresponding frames with dials and buttons (non-Thrustmaster). I am very interested in how this progresses. I already have pair of Cougar MFDs, but I would rather 1:1 scale replicas of the Hornet. Having them as a package is a lot nicer for than having to start with a 3d printed frame, install and wire buttons then try to match a monitor. I also like Stang's plans/kits for using full scale panel, but simplified to be flat with 27" monitor to drive the entire panel. I am in no hurry. So, I can't wait to see what pops up before I have the time/money/space to commit to a Hornet pit. [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
markturner1960 Posted September 13, 2020 Author Share Posted September 13, 2020 Hi, I am still having the issue where I have to set up the displays in windows every time I start the PC, as it reverts to the monitors native resolution which is 3840 x 2160, rather than the 2160 x 1440 res I am currently running, which seems to give a good balance of image quality and performance with my screen set up. Is there a way to force windows to accept my preferred setting and stop it changing it? Thanks System specs: PC1 :Scan 3XS Ryzen 5900X, 64GB Corsair veng DDR4 3600, EVGA GTX 3090 Win 10, Quest Pro, Samsung Odyssey G9 Neo monitor. Tir5. PC2 ( Helo) Scan 3XS Intel 9900 K, 32 GB Ram, 2080Ti, 50 inch Phillips monitor F/A-18C: Rhino FFB base TianHang F16 grip, Winwing MP 1, F-18 throttle, TO & Combat panels, MFG crosswind & DFB Aces seat Viper: WinWing MFSSB base with F-16 grip, Winwing F-16 throttle, plus Vipergear ICP. MFG crosswind rudders. Helo ( Apache) set up: Virpil collective with AH64D grip, Cyclic : Rhino FFB base & TM F18 grip, MFG crosswind rudders, Total controls AH64 MFD's, TEDAC Unit. Link to comment Share on other sites More sharing options...
HonerT2 Posted November 21, 2020 Share Posted November 21, 2020 Hi, been trying all Month to my cube sim MFD’s working..... The problem seems to a windows display set up related issue. Extend the desktop to both. I have been trying everything. CUBESIM MFD SCREEN INSTRUCTION 1.position all monitor like the pic[Windows monitor set,not real position] 2.copy the cubesim.lua to Eagle Dynamic/DCS World/Config/MonitorSetup or Eagle Dynamic/DCS World OpenBeta/Config/MonitorSetup 3.open DCS change resolution to [3520 X 1080] 4.cancel fullscreen option 5.select cubesim screen set in DCS 6.enjoy! However I get Main screen showing 1/4 to right of monitor and on cannot control anything. They have sent me a second LUA file but setup is the same. Hopefully someone can help. I have a 32" VIOTEK monitor res is 1920 X 1080 Ordered two of the 120 MFD's. Also included LUA file Will attach files. Been trying for a month to get it to work. HELP!!!!! name = _('CUBESIM'); Description = 'Left MFCD on the left monitor,Right MFCD on the right and camera on the center' Viewports = { Center = { x = 1600; y = 0; width = 1920; height = 1080; viewDx = 0; viewDy = 0; aspect = 1920 / 1080; } } LEFT_MFCD = { x = 80; y = 0; width = 600; height = 600; } RIGHT_MFCD = { x = 880; y = 0; width = 600; height = 600; } F14_HSD = { x = 80; y = 0; width = 600; height = 600; } F14_VDI = { x = 880; y = 0; width = 600; height = 600; } UIMainView = Viewports.Center GU_MAIN_VIEWPORT = Viewports.Center Link to comment Share on other sites More sharing options...
markturner1960 Posted November 23, 2020 Author Share Posted November 23, 2020 Can you post how your monitors are arranged within windows? System specs: PC1 :Scan 3XS Ryzen 5900X, 64GB Corsair veng DDR4 3600, EVGA GTX 3090 Win 10, Quest Pro, Samsung Odyssey G9 Neo monitor. Tir5. PC2 ( Helo) Scan 3XS Intel 9900 K, 32 GB Ram, 2080Ti, 50 inch Phillips monitor F/A-18C: Rhino FFB base TianHang F16 grip, Winwing MP 1, F-18 throttle, TO & Combat panels, MFG crosswind & DFB Aces seat Viper: WinWing MFSSB base with F-16 grip, Winwing F-16 throttle, plus Vipergear ICP. MFG crosswind rudders. Helo ( Apache) set up: Virpil collective with AH64D grip, Cyclic : Rhino FFB base & TM F18 grip, MFG crosswind rudders, Total controls AH64 MFD's, TEDAC Unit. Link to comment Share on other sites More sharing options...
MustangSally Posted November 25, 2020 Share Posted November 25, 2020 You must have your monitor setup like the following in Windows....right click desktop - display settings Under multiple displays the 'Extend option is enabled, not duplicated Monitor identification should read from right to left 1, 2 and 3 Your res in DCS should be 3520x1080 with full screen unchecked And ensure you select the cubesim profile Ryzen 9 7950X3D - MSI MAG X670E TomaHawk MB, ASUS ROG Ryujin III 360 AIO 64gig Corsair DDR5@6000, Gigabyte GeForce RTX 4090 AORUS Winwing Super Taurus, Orion2, TO / Combat panels, Collective with Topgun MIP Winwing Skywalker pedals, NLR Boeing Mil Edition Simpit, Trackir Link to comment Share on other sites More sharing options...
markturner1960 Posted November 25, 2020 Author Share Posted November 25, 2020 Once you have that working correctly, if required due to performance reasons ( obviously you now need to run DCS at a substantially higher resolution and you have not mentioned your hardware or settings) you can re arrange the smaller screens vertically within windows, but that’s another story and will mean altering the .lua file accordingly........ System specs: PC1 :Scan 3XS Ryzen 5900X, 64GB Corsair veng DDR4 3600, EVGA GTX 3090 Win 10, Quest Pro, Samsung Odyssey G9 Neo monitor. Tir5. PC2 ( Helo) Scan 3XS Intel 9900 K, 32 GB Ram, 2080Ti, 50 inch Phillips monitor F/A-18C: Rhino FFB base TianHang F16 grip, Winwing MP 1, F-18 throttle, TO & Combat panels, MFG crosswind & DFB Aces seat Viper: WinWing MFSSB base with F-16 grip, Winwing F-16 throttle, plus Vipergear ICP. MFG crosswind rudders. Helo ( Apache) set up: Virpil collective with AH64D grip, Cyclic : Rhino FFB base & TM F18 grip, MFG crosswind rudders, Total controls AH64 MFD's, TEDAC Unit. Link to comment Share on other sites More sharing options...
Sydy Posted February 9, 2021 Share Posted February 9, 2021 On 8/31/2020 at 10:18 AM, Supmua said: Try this. I'm at work so can't test any of this but it should give you a general idea of how to proceed. 1. In Windows display settings, change main panel res to 2560x1440 2. In Cubesim lua, change Center width, height to 2560, 1440 3. In DCS settings, change display resolution to 2560+800+800+800, 1440 Gents, I just would like to say thank you for the tips. It helped a lot for my set up. Interesting is that I run on 3840x2160, corrected for 2 mfd screens (+1600) and it runs fine, around 35fps+. in very few instances I saw a drop to 25~29fps. I tried the 2560x1440 (plus correction) and saw no real gain in fps, so I returned to 4k. Anyway, thank you for the post and messages. All the best, Sydy Link to comment Share on other sites More sharing options...
rapid Posted March 24, 2021 Share Posted March 24, 2021 I have two of these monitors on order from Cubesim. I found it interesting that someone had an issue that depending on how his screens were configured in Windows that it would impact his FPS. Is this still the case or has this been resolved? Asus ROG Crosshair Hero VIII , Ryzen 3900X, Nzxt Kraken Z73, Vengence RBG Pro DDR4 3600mhz 32 GB, 2x Corsair MP 600 pcie4 M.2 2 TB , 2x Samsung Qvo SSD 2x TB, RTX 3090 FE, EVGA PSU 800watt, Steelseries Apex Pro. TM WartHog,TM TPR, Track IR, TM 2 x MFD, Asus VG289Q, Virpil Control Panel#2 Link to comment Share on other sites More sharing options...
Toni Carrera Posted July 25, 2021 Share Posted July 25, 2021 Hi Fellow Pilots, I have my new CubeSim screens that I want to use obviously with DCS. I can't DDI get the screens to show on the respective devices. Here is the setup that I have in use; My Monitors are configured as follows; Attached Image 1 – 1920 x 1080 2 – 2560 x 1080 (Main Monitor and also only screen that DCS runs on) 3 – 1920 x 1080 4 – CubeSim Screen 5 – CubeSim Screen Please can you assist me with how I configure DCS to run on screen number 2 and CubeSim screens, 4 & 5 I sincerely hope someone out there can help me, It has taken me 8 months to get to this final part Thank you Toni Carrera (Ice Rhino) ThrustMaster HOTAS Warthog Throttle & A10C Stick, ThrustMaster F/A-18C Stick, ThrustMaster TFRP Pedals, ThrustMaster Cougars x 2, fitted to CubeSim USB Screens, TrackIR 4 Active LED & Cap Reflector, Stream Deck XL Intel® Core™ i7-5820K 12 Core Processor, 32GB RAM, 1 x 500GB SSD, 2 x 256GB SSD, 1 x 1TB SSD 4 x 4TB Western Digital Mechanical. 2 x ASUS GTX 1080's SLI, ASUS 29" Ultrawide flanked by 2 x 22" IPS Monitors Link to comment Share on other sites More sharing options...
jonsky7 Posted August 2, 2021 Share Posted August 2, 2021 On 7/25/2021 at 7:56 AM, Ice Rhino said: Hi Fellow Pilots, I have my new CubeSim screens that I want to use obviously with DCS. I can't DDI get the screens to show on the respective devices. Here is the setup that I have in use; My Monitors are configured as follows; Attached Image 1 – 1920 x 1080 2 – 2560 x 1080 (Main Monitor and also only screen that DCS runs on) 3 – 1920 x 1080 4 – CubeSim Screen 5 – CubeSim Screen Please can you assist me with how I configure DCS to run on screen number 2 and CubeSim screens, 4 & 5 I sincerely hope someone out there can help me, It has taken me 8 months to get to this final part Thank you @Ice Rhino Try this monitor config file, copy it to Saved Games\DCS\Config\Monitorsetup\ Main plus 2 cubesim.lua Then in DCS System settings menu Set your resolution to 2560x1680, if that is not a selectable resolution, you can type it in the box. Set your aspect ratio to 1.5238095238, can also be typed Choose the config file, name is Main Cubesimx2 Click "OK" DCS should restart Link to comment Share on other sites More sharing options...
Toni Carrera Posted August 2, 2021 Share Posted August 2, 2021 (edited) Thanks jonsky7, I will go and try that right now I will report back, thank you Edited August 2, 2021 by Ice Rhino Toni Carrera (Ice Rhino) ThrustMaster HOTAS Warthog Throttle & A10C Stick, ThrustMaster F/A-18C Stick, ThrustMaster TFRP Pedals, ThrustMaster Cougars x 2, fitted to CubeSim USB Screens, TrackIR 4 Active LED & Cap Reflector, Stream Deck XL Intel® Core™ i7-5820K 12 Core Processor, 32GB RAM, 1 x 500GB SSD, 2 x 256GB SSD, 1 x 1TB SSD 4 x 4TB Western Digital Mechanical. 2 x ASUS GTX 1080's SLI, ASUS 29" Ultrawide flanked by 2 x 22" IPS Monitors Link to comment Share on other sites More sharing options...
jonsky7 Posted August 3, 2021 Share Posted August 3, 2021 16 hours ago, Ice Rhino said: Thanks jonsky7, I will go and try that right now I will report back, thank you @Ice Rhino I've never had a monitor to the left of my main monitor in windows settings, so I'm interested to know how it turned out. Link to comment Share on other sites More sharing options...
Toni Carrera Posted August 4, 2021 Share Posted August 4, 2021 I am not purposely delaying to build the suspense, I have been pulled away on business and will not be home until Friday. I will aim to test this on early morning on Saturday morning and report back 1 Toni Carrera (Ice Rhino) ThrustMaster HOTAS Warthog Throttle & A10C Stick, ThrustMaster F/A-18C Stick, ThrustMaster TFRP Pedals, ThrustMaster Cougars x 2, fitted to CubeSim USB Screens, TrackIR 4 Active LED & Cap Reflector, Stream Deck XL Intel® Core™ i7-5820K 12 Core Processor, 32GB RAM, 1 x 500GB SSD, 2 x 256GB SSD, 1 x 1TB SSD 4 x 4TB Western Digital Mechanical. 2 x ASUS GTX 1080's SLI, ASUS 29" Ultrawide flanked by 2 x 22" IPS Monitors Link to comment Share on other sites More sharing options...
Skunk 2-1 Posted December 7, 2021 Share Posted December 7, 2021 Hi, I have now a new problem. After installing a new Cockpit Livery, DCS is not using the MFD Monitors (3 and 4) anymore. This is my Monitor setup, and DCS is now using the top left corner of Monitor 2 as x=0;y=0. So the DCS screen is now pushed by 1600 pixel right on Monitor 1, which I do not use for DCS. On Monitor 3 and 4 is the normal windows background and windows identified the monitors correctly and I can use them . } My monitorconfig lua: { Center = { x = 1600; y = 0; width = 3440; height = 1440; viewDx = 0; viewDy = 0; aspect = 3440 / 1440; } } LEFT_MFCD = { x = 80; y = 0; width = 600; height = 600; } RIGHT_MFCD = { x = 880; y = 0; width = 600; height = 600; Just for kicks, I uninstalled the Livery, but with no effect. Help and ideas would be really appreciated, Cheers Link to comment Share on other sites More sharing options...
Skunk 2-1 Posted December 8, 2021 Share Posted December 8, 2021 Solved it. Shutdown the PC, disconnected the MFD's, restarting DCS, switched to single Monitor, shutingdown the PC, reconnected the MFD's, restarted DCS, reinstalled Multimonitor again. Cheers Link to comment Share on other sites More sharing options...
Docsnuggles Posted February 6, 2022 Share Posted February 6, 2022 HI, did ED change something in the export name of the FA18? everything works, only the FA18 does not send to the monitors anymore. A10A/C/C2, F16, M2K, Harrier, Ka50, SA342,... all work, only the Hornet does not show on the external monitor. = function(p) return p; end; name = _('CUBESIM 8'); Description = 'Left MFCD on the left monitor,Right MFCD on the right and camera on the center' Viewports = { Center = { x = 0; y = 0; width = 3840; height = 1080; viewDx = 0; viewDy = 0; aspect = 3840 / 1080; } } -- General LEFT_MFCD = { x = 3920; y = 0; width = 600; height = 600; } RIGHT_MFCD = { x = 4720; y = 0; width = 600; height = 600; } 0 = { x = 3920; y = 0; width = 600; height = 600; } 1 = { x = 4720; y = 0; width = 600; height = 600; } --JF17 JF17_LEFT_MFCD = { x = 3970; y = 80; width = 520; height = 750; } JF17_RIGHT_MFCD = { x = 4770; y = 80; width = 520; height = 750; } -- F14 F14_HSD = { x = 3920; y = 0; width = 600; height = 600; } F14_VDI = { x = 4720; y = 0; width = 600; height = 600; } RIGHTJ_MFCD = { x = 4740; y = 30; width = 560; height = 830; } LEFTJ_MFCD = { x = 3940; y = 30; width = 560; height = 830; } -- M2000 M2000C_VTB = { x = 4720; y = 0; width = 600; height = 600; } M2000_RWR = { x = 3920; y = 0; width = 600; height = 600; } RWR = { x = 3920; y = 0; width = 600; height = 600; } -- Viggen VIGGEN_RADAR = { x = 4720; y = 0; width = 600; height = 600; } VIGGEN_NAV = { x = 3840; y = 60; width = 44; height = 44; } --Gazelle --SA342_TV SA342_TV = { x = 4740; y = 100; width = 590; height = 495; } -- SA342_RWR SA342_RWR = { x = 4140; y = 50; width = 300; height = 300; } --SA342_NADIR NADIR = { x = 3840; y = 0; width = 300; height = 300; } --SA342_WP1 SA342_WP1 = { x = 4730; y = 10; width = 300; height = 90; } --SA342_UHF SA342_UHF = { x = 4040; y = 500; width = 300; height = 100; } --SA342_FM SA342_FM = { x = 4140; y = 400; width = 300; height = 100; } --Ka-50 PVI = { x = 3960; y = 5; width = 200; height = 95; } Ekran = { x = 4180; y = 5; width = 100; height = 95; } UV26 = { x = 4290; y = 5; width = 150; height = 95; } Shkval = { x = 3940; y = 100; width = 590; height = 495; } ABRIS = { x = 4780; y = 25; width = 500; height = 570; } -- Mi-8 UV_26 = { x = 4180; y = 5; width = 100; height = 95; } -- --g_panel_page = --{ -- x = 4780; -- y = 250; -- width = 590; -- height = 495; --} UIMainView = Viewports.Center GU_MAIN_VIEWPORT = Viewports.Center Im actually experimenting but it seems ED changed the names, I did not find a hint, so does anyone know? Link to comment Share on other sites More sharing options...
Docsnuggles Posted February 6, 2022 Share Posted February 6, 2022 Found a solution, simply renamed the ports, now it works again: F18_LEFT = { x = 3920; y = 0; width = 600; height = 600; } F18_RIGHT = { x = 4720; y = 0; width = 600; height = 600; } Additional in the MDI_left_viewport_cfg.lua: --ViewportHandling dofile(LockOn_Options.common_script_path.."ViewportHandling.lua") update_screenspace_diplacement(1, true, 0) try_find_assigned_viewport("F18_LEFT") and in right also. Link to comment Share on other sites More sharing options...
Cosigin Posted September 27, 2022 Share Posted September 27, 2022 Does anyone know why when I am in f10 map I cannot select units? Link to comment Share on other sites More sharing options...
Cosigin Posted September 28, 2022 Share Posted September 28, 2022 Does anyone know why when I am in f10 map I cannot select units? Anyone here with cubesim suffering from f10 map not working not allowing to select units? Link to comment Share on other sites More sharing options...
Recommended Posts