Drac Posted October 18, 2020 Share Posted October 18, 2020 I didn't know there were choices. I ordered the one in the link I posted. It's white. What's the difference in the choices offered? Edit........I went back to my link and saw the choices. Mine is the cheapest one but I can't imagine it feeling any smoother pushing through it. I went to purchase and the shipping and processing cost is as much as the unit itself. Was that the case when you ordered yours? Link to comment Share on other sites More sharing options...
BuzzU Posted October 18, 2020 Share Posted October 18, 2020 I went to purchase and the shipping and processing cost is as much as the unit itself. Was that the case when you ordered yours? Yes, it was. I don't know why but he ships in a box that could hold 300-400 detents when a small padded envelope would work. Buzz Link to comment Share on other sites More sharing options...
Drac Posted October 18, 2020 Share Posted October 18, 2020 Yes, it was. I don't know why but he ships in a box that could hold 300-400 detents when a small padded envelope would work. I decided to go the cheap way...my wife's nail filer. Are you or anyone getting 100% at full mil-power? I'm only able to get 99% using the user curves. Link to comment Share on other sites More sharing options...
=Panther= Posted October 18, 2020 Share Posted October 18, 2020 I decided to go the cheap way...my wife's nail filer. Are you or anyone getting 100% at full mil-power? I'm only able to get 99% using the user curves. That is DCS, the detent position doesn't match 100%. It is like that with the Hornet, and the Viper, and maybe others. Twitch Channel [sIGPIC][/sIGPIC] Virtual Thunderbirds, LLC | Sponsored by Thrustmaster Z390 Aorus Xtreme, i9 9900k, G.SKILL TridentZ Series 32GB, 1080ti 11GB, Obutto R3Volution, Thrustmaster HOTAS Warthog, TPR, Cougar MFDs, FSSB R3L, JetSeat, Oculus Rift S, Buddy-Fox A-10C UFC, F/A-18C UFC, Tek Creations F-16 ICP Link to comment Share on other sites More sharing options...
BuzzU Posted October 18, 2020 Share Posted October 18, 2020 (edited) The Viper is close enough that I don't mess with it. The Hornet needed a new curve. Edited October 19, 2020 by BuzzU Buzz Link to comment Share on other sites More sharing options...
oldcrusty Posted October 18, 2020 Share Posted October 18, 2020 Just got done with the detent... Why oh why haven't I done this before:doh: My main concern was filing at different angles between left and right stopper. Came out perfect and it feels just right. This also allowed me to straighten up the curves in the axes setup. They are almost linear. As soon as I go past the bumps I can see the AB rings lighting up barely. I went to F2 view looking at the nozzles at a slight angle (at night). When you just barely enter AB, it takes 2 secs for the fuel to ignite. Of course in cockpit view you'll see a huge jump in FF. @Drac At low altitude the MIL will show you 98%, creeping through 99 till you climb around 7k feet, irc. Then you'll be at 100% until roughly 26k (?). It'll creep down to around 98% past 30k. That's what I see in DCS Hornet, would have to look it up... Link to comment Share on other sites More sharing options...
Drac Posted October 18, 2020 Share Posted October 18, 2020 Thanks everybody for your responses. Love the ability to go Mil-Power quickly without the concern of going AB. @Gripes323 - My left stop was a little bit more difficult for me...had to work on that side a little more. Link to comment Share on other sites More sharing options...
BuzzU Posted October 19, 2020 Share Posted October 19, 2020 I look at the fuel flow to check when AB starts. Buzz Link to comment Share on other sites More sharing options...
lxsapper Posted December 31, 2020 Share Posted December 31, 2020 I use TM TARGET Script for a custom axis response dor each plane, I get two perfectly linear response zones (For Dry and Wet thrust), much better than the messy thing you get trying to make a custom curve in DCS. Link to comment Share on other sites More sharing options...
Recommended Posts