KiwiOz Posted November 7, 2020 Share Posted November 7, 2020 Broadcast target, how is this done, cant seem to find anything on it Link to comment Share on other sites More sharing options...
Dagobert666 Posted November 7, 2020 Share Posted November 7, 2020 https://wiki.hoggitworld.com/view/HOTAS_Controls 1) Set a SPI 2) SOI to TAD [3) The Data Management Switch (DMS) DMS-Left-Long----->Broadcast SPI thorugh JTRS Datalink] = NOT CORRECT 3) Target Management Switc TMS-Left-Long----->Broadcast SPI thorugh JTRS Datalink Link to comment Share on other sites More sharing options...
SJBMX Posted November 7, 2020 Share Posted November 7, 2020 It's TMS Left Long now. (DMS Left Long turns the HMD on and off.) When you're broadcasting, you'll see "SPI ON" in the upper right corner of your TAD. Link to comment Share on other sites More sharing options...
Dagobert666 Posted November 7, 2020 Share Posted November 7, 2020 ups sorry Link to comment Share on other sites More sharing options...
zildac Posted November 7, 2020 Share Posted November 7, 2020 I get the broadcast SPI, but how do you send a target (red triangle on receiving parties TAD)? 12900KF | Maximus Hero Z690 | ASUS 4090 TUF OC | 64GB DDR5 5200 | DCS on 2TB NVMe | WarBRD+Warthog Stick | CM3 | TM TPR's | Varjo Aero Link to comment Share on other sites More sharing options...
icemaker Posted November 7, 2020 Share Posted November 7, 2020 Has before, create your SPI as desired make your TAD as SOI, then with slew move the small cross to your wingman, hook it with TMS up short and select the Send OSB (on the right) ti will have the net ID below the Send option. 1 Link to comment Share on other sites More sharing options...
zildac Posted November 7, 2020 Share Posted November 7, 2020 Thanks icemaker 12900KF | Maximus Hero Z690 | ASUS 4090 TUF OC | 64GB DDR5 5200 | DCS on 2TB NVMe | WarBRD+Warthog Stick | CM3 | TM TPR's | Varjo Aero Link to comment Share on other sites More sharing options...
KiwiOz Posted November 8, 2020 Author Share Posted November 8, 2020 thanks guys sorry i thought a target was separate to a SPI So the process is now; find a target, make it as a spi then TMS long to broadcast spi that is covered and understand what i am trying to do is to have a target that is red show up in my HMS like the video I am assuming incorrectly that it cant be separate, IE i do not want to broadcast my current spi but to be able to make a target point or current target and broadcast that OR maybe have Target PTS like Mark points maybe? What icemaker is saying. Find a target, make it spi, and hook to wingman send ? this will then create a red triangle, what about your entire group? Link to comment Share on other sites More sharing options...
icemaker Posted November 8, 2020 Share Posted November 8, 2020 you will have to do it one wingman at a time Link to comment Share on other sites More sharing options...
Scubamurph Posted November 10, 2020 Share Posted November 10, 2020 With the red triangle you are actually sending a single target tasking to a specific wingman. For the entire flight to see a target you need to create your SPI then broadcast it - they will see the 2 tier wedding cake in blue. You would then get your flight to capture it and make it SPI for themselves. You would usually designate specific targets to your wingmen individually so they are not all attacking the same target. If you found a target of opportunity that you wanted everyone to engage then use the SPI broadcast to show where the target is. Link to comment Share on other sites More sharing options...
Recommended Posts