Zeus67 Posted July 21, 2021 Share Posted July 21, 2021 ROUTE navigation, formerly known as NSEQ navigation, allows the Harrier to fly a subset of the mission flightplan. There are three types of Routes, although only two are enabled: 1. SEQ: Sequential, in which a route is created following all the waypoints sequentially to a selected terminus. 2. NSEQ: Non sequential, in which a route is created by programing a sequence of waypoints. These waypoints do not need to be in sequential order. 3. RSEQ: Not enabled in the real aircraft. Creates a sequential route similar to the flight plan by using the GPS, HOW TO create a ROUTE 1. Select the EHSD Data Page. 2. Select the NSEQ option (PB11) 3. The ODU will show the following options: ODU 1: IGRS, ODU 2: EGRS, ODU 3: TERM, ODU 4: PROG, ODU 5: RSET. 3.1 IGRS: Creates a non sequential ingress route TO a target. The last entry is considered to be a target. If the last entry has a n offset, the offset it the last navigation point. 3.2 EGRS: Creates a non sequential egress route FROM a target. The first entry is the last IGRS point (if it exists). The last entry is considered the HOME waypoint. 3.3 TERM: Creates a sequential flight route from the aircraft position to the selected terminus waypoint or designated targetpoint. If no targetpoint was designated, the terminus waypoint is considered to be the target. If the waypoint has an offset, the offset is considered to be the end point. 3.3 PROG: When selected enables the programing of a route. 3.4 RSET: Clears the selected route. 4. Seelct the route to be created by clicking on ODU buttons 1 to 3. The selected option will be colonized (a colon will appear). 5. Click on the PROG ODU button. 5.1 The ODU will change to the following options: ODU 1: WYPT, ODU 2: MKPT (Only for IGRS and EGRS), ODU 3: TGPT, ODU 4: PROG (it will be colonized), ODU 5: Seelcted route option (IGRS, EGRS or TERM). 5.2 ODU 1 to 3 indicates the ype of steerpoint that will be used to create the route. By default WYPT is colonized, meaning that waypoints will be used. 5.3 Select the type of steerpoint: Waypoint (WYPT) {DEFAULT}, Markpoint (MKPT) [only for IGRS and EGRS} or Tragetpoint (TGPT). 5.4 The UFC scratchpad will show the last enterd waypoint. 0 if the route is empty. For IGRS and EGRS, the EHSD will show the routes selected waypoints. IGRS route is on top, EGRS route is at the bottom. 5.5 For TERM routes, a waypoint is required. You can also select a targetpoint, but the route will be createf to the terminus waypoint and then to the targetpoint. 5.6 YOu can change the type of route by clicking on ODU 5. Its label will cycle from IGRS to EGRS to TERM back to IGRS. 6. When you have finished, click on the EHSD DATA button. HOW TO use a ROUTE 1. ROUTE can only be selected when the aircraft master mode is not in AG (NAV, VSTOL or AA). 2. In the EHSD navigation page select the ROUTE option (PB10) 3. The ODU will show the available options: ODU 1: SEQ (DEFAULT and always available), ODU 2: NSEQ (Available only if an IGRS and/or an EGRS route has been defined), ODU 3: RSEQ (Not available) 4. Select the option in the ODU. 4.1 The selected option will be colonized. 4.2 The ROUTE button label will change to the selected route option: SEQ oe NSEQ and it will be boxed, indicating that it is active. 4.3 The route will be shown in the EHSD map. 4.4 For NSEQ routes, the IGRS route will be a solid dark purple line. The EGRS route will be a dashed purple line. 5. Pressing the SEQ or NSEQ boxed button will unbox it. The legend will change to ROUTE and the route navigation will be disabled. 6 2 "Programming today is a race between software engineers striving to build bigger and better idiot-proof programs, and the Universe trying to produce bigger and better idiots. So far, the Universe is winning." "The three most dangerous things in the world are a programmer with a soldering iron, a hardware type with a program patch and a user with an idea." Link to comment Share on other sites More sharing options...
Shiroka Posted July 21, 2021 Share Posted July 21, 2021 The NSEQ gets stuck on once you select it for the first time. Then even if you deselect it you can't remove the NSEQ overlay or reset the string in data. 1 Link to comment Share on other sites More sharing options...
Hamster0 Posted July 22, 2021 Share Posted July 22, 2021 3 hours ago, Shiroka said: The NSEQ gets stuck on once you select it for the first time. Then even if you deselect it you can't remove the NSEQ overlay or reset the string in data. Same problem for me Link to comment Share on other sites More sharing options...
Shrike88 Posted July 22, 2021 Share Posted July 22, 2021 5 hours ago, Shiroka said: The NSEQ gets stuck on once you select it for the first time. Then even if you deselect it you can't remove the NSEQ overlay or reset the string in data. +1 Thanks hopefully will be addressed. Link to comment Share on other sites More sharing options...
Wisky Posted July 22, 2021 Share Posted July 22, 2021 it is already fixed internally, will be in next patch/hotfix 1 Link to comment Share on other sites More sharing options...
deephack Posted July 23, 2021 Share Posted July 23, 2021 Good instructions, these should be pinned. https://www.youtube.com/user/deephack Link to comment Share on other sites More sharing options...
LastRifleRound Posted September 12, 2021 Share Posted September 12, 2021 Can anyone point me to some good demonstrations of these in use? I had a grasp on the old way of doing it, but I can't this new way to work at all. Also, does TOT now work from a route perspective, or is it still bugged? Link to comment Share on other sites More sharing options...
Shiroka Posted September 12, 2021 Share Posted September 12, 2021 36 minutes ago, LastRifleRound said: Also, does TOT now work from a route perspective, or is it still bugged? Still bugged but being worked on apparently. Link to comment Share on other sites More sharing options...
gmangnall Posted August 1, 2022 Share Posted August 1, 2022 TERM no longer seems to be working Link to comment Share on other sites More sharing options...
Recommended Posts