Jump to content

rudder wheelbrake assignment problem


Recommended Posts

Hi, despite copying over my old config file, when setting up my new PC some assigments are missing. One of these is the wheelbrake to my rudders. Easil;y added you say, but in my case, not. I checked in control panel and its all working fine there.

 

when I go to controls in DCS, and try and assign either an axis or by using the "add" button, no input is picked up when I press the toebrake. So I cant assign it.  Any ideas?

System specs: PC1 :Scan 3XS Ryzen 5900X, 64GB Corsair veng DDR4 3600, EVGA GTX 3090 Win 10, Quest Pro, Samsung Odyssey G9 Neo monitor. Tir5. PC2 ( Helo) Scan 3XS Intel 9900 K, 32 GB Ram, 2080Ti, 50 inch Phillips monitor

 F/A-18C: Rhino FFB base TianHang F16 grip, Winwing MP 1, F-18 throttle, TO & Combat panels, MFG crosswind & DFB Aces  seat :cool:                       

Viper: WinWing MFSSB base with F-16 grip, Winwing F-16 throttle, plus Vipergear ICP. MFG crosswind rudders. 

Helo ( Apache) set up: Virpil collective with AH64D grip, Cyclic : Virpil CM3 base & TM F18 grip, MFG crosswind rudders, Total controls AH64 MFD's,  TEDAC Unit. 

 

Link to comment
Share on other sites

Check closely for a duplicate axis assignment for the wheelbrakes.

Don B

EVGA Z390 Dark MB | i9 9900k CPU @ 5.1 GHz | Gigabyte 4090 OC | 64 GB Corsair Vengeance 3200 MHz CL16 | Corsair H150i Pro Cooler |Virpil CM3 Stick w/ Alpha Prime Grip 200mm ext| Virpil CM3 Throttle | VPC Rotor TCS Base w/ Alpha-L Grip| Point Control V2|Varjo Aero|

Link to comment
Share on other sites

Thanks, but nothing that I can see Don....

System specs: PC1 :Scan 3XS Ryzen 5900X, 64GB Corsair veng DDR4 3600, EVGA GTX 3090 Win 10, Quest Pro, Samsung Odyssey G9 Neo monitor. Tir5. PC2 ( Helo) Scan 3XS Intel 9900 K, 32 GB Ram, 2080Ti, 50 inch Phillips monitor

 F/A-18C: Rhino FFB base TianHang F16 grip, Winwing MP 1, F-18 throttle, TO & Combat panels, MFG crosswind & DFB Aces  seat :cool:                       

Viper: WinWing MFSSB base with F-16 grip, Winwing F-16 throttle, plus Vipergear ICP. MFG crosswind rudders. 

Helo ( Apache) set up: Virpil collective with AH64D grip, Cyclic : Virpil CM3 base & TM F18 grip, MFG crosswind rudders, Total controls AH64 MFD's,  TEDAC Unit. 

 

Link to comment
Share on other sites

Tried assigning it manually rather than just pressing the brake?

Asus Z690 Hero | 12900K | 64GB G.Skill 6000 | 4090FE | Reverb G2 | VPC MongoosT-50CM2 + TM Grips  | Winwing Orion2 Throttle | MFG Crosswind Pedals

Link to comment
Share on other sites

Using the Key / Button drop down menu.

 

Trial and error to get the right axis, but that shouldn't present too much trouble when there's only three.

Asus Z690 Hero | 12900K | 64GB G.Skill 6000 | 4090FE | Reverb G2 | VPC MongoosT-50CM2 + TM Grips  | Winwing Orion2 Throttle | MFG Crosswind Pedals

Link to comment
Share on other sites

thanks, I was not able to get it to work, using the suggestions, but was able to copy over the relevant section of teh .lua file from my old install and it works! But thanks!

System specs: PC1 :Scan 3XS Ryzen 5900X, 64GB Corsair veng DDR4 3600, EVGA GTX 3090 Win 10, Quest Pro, Samsung Odyssey G9 Neo monitor. Tir5. PC2 ( Helo) Scan 3XS Intel 9900 K, 32 GB Ram, 2080Ti, 50 inch Phillips monitor

 F/A-18C: Rhino FFB base TianHang F16 grip, Winwing MP 1, F-18 throttle, TO & Combat panels, MFG crosswind & DFB Aces  seat :cool:                       

Viper: WinWing MFSSB base with F-16 grip, Winwing F-16 throttle, plus Vipergear ICP. MFG crosswind rudders. 

Helo ( Apache) set up: Virpil collective with AH64D grip, Cyclic : Virpil CM3 base & TM F18 grip, MFG crosswind rudders, Total controls AH64 MFD's,  TEDAC Unit. 

 

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...