Can I adjust HARM page Curser speeds

[Fakum]

I am using a microstick on my throttle and it works just fine for the RADAR curser as I have the option to adjust its curves using "RDR Curser Switch" X & Y Axis in DCS Controls Options. When I go from Air to Air mode to Air to Ground, and bring up the HARMs page, the curser speed is way too responsive and I want to tone it down I cant find any adjustment options or any other posts relative to this question. Any advice would be greatly appreciated. Thank you,

[Skyracer]

gET THE SLEW UPGRADE

 

Sorry for caps

[Fakum]

I dont have a Warthog, I have a Virpil, but my point is, is there no software (curve) adjustment in DCS Control Options to adjust the slew rate for the HARM Curser?

 

[Clean]

I've noticed the same with my Virpil throttle for the HARM cursor; it's really anything on the weapon page but the HARM is especially noticeable. I also use the roll wheel thing on the right side for radar elevation, and since it's "buttons" rather than axis, there is no way to adjust speed or curves. Even though it works great for the F/A-18C, the F-16 has it set a lot more movement per click.

[Northstar98]

Yeah, noticed the same with the gate control ministick on my VKB MCG Pro.

For every other aircraft and on every other MFD page with a cursor, it's absolutely fine, but on exclusively the F-16CM's WPN page for the HARM it's incredibly sensitive and races across the screen with minimal input, which means that HAS mode is rather difficult to use.

Edited November 18, 2021 by Northstar98

[Mustang25]

This has been a bug since HARMs were first released but apparently ED doesn’t want to fix it. 

[_SteelFalcon_]

This. The cursor speed is not identical across all the sensors, which in terms makes adding curves slow down the cursor on the radar screen way too much, while making it acceptable on the harm wpn page.

 

if at least all the cursors would be equally slow/fast, it‘d make adding curves to mini-sticks way more beneficial across all the sensors

[Fakum]

at least i can adjust the radar curser in DCS Axis options, cant to anything apparently for the HARM curser within DCS

[Al-Azraq]

Same here, moving the cursor through the HAS page is tricky because the cursor moves so fast.

[darkman222]

The speed of the cursor on the MFD seems to differ from the speed the cursor has on the FCR. Whats good on the FCR is still too fast for Maverics on the MFD. Seems to be a related issue.

[Fakum]

Honestly, i havnt even used the Mavericks on the Viper to date, So I dont know about that, will have to test that out as well.

[Northstar98]

Wanted to bump this as this issue also affects the HAD page for the newly implemented HTS, as well as the HSD cursor and also somewhat for the AG FCR.

The cursor speed is fine for the CRM FCR, Maverick WPN page and TGP page, but it jumps around, is twitchy and moves too fast for the HSD cursor, HARM WPN page and HAD page.

The cursor speed is also inconsistent on the AG FCR page, leading to it jumping around (though not as bad as some of the aforementioned pages).

 

F-16CM-50_cursor_speeds.trk

Edited January 16, 2022 by Northstar98

[FoxOne007]

47 minutes ago, Northstar98 said:

Wanted to bump this as this issue also affects the HAD page for the newly implemented HTS, as well as the HSD cursor and also somewhat for the AG FCR.

The cursor speed is fine for the CRM FCR, Maverick WPN page and TGP pages, but jumps around, is twitchy and moves too fast for the HSD cursor, HARM WPN page and HAD page.

 

F-16CM-50_cursor_speeds.trk 225.66 kB · 0 downloads

To add onto this, cursor speed should be the same on all pages with a cursor, this goes for the F-18 too btw, the cursor speed on that jet is a complete mess

Edited November 19, 2021 by FoxOne007