Ramstein Posted September 3, 2021 Share Posted September 3, 2021 (edited) Jtac not moving to 2nd tank after killing first Jtac lit tank. Have a group of enemy tank lit up by Jtac, using Tac to mark a group of tank. using Mavericks with F-18. After calling up Jtac, they lite up/mark one of the tanks, I kil it with Maverick, then, I expect the Jtac to lite up another tank, etc, etc, until all ammo is expended and or tanks are all dead. Jtac stayed lock on first tank after tank was killed. I looked for a similar question in the F-18 threads, and did not find the answer. Thanx. I did find this, but not sure if is the answer.. btw, this is multiplayer, with a host running F10 script. I found this in the Combined arms threads after more searching... not sure if this is relevent. 3 Posted June 27 JTACs don't task you to do DEAD. The Ground Commander has an intent, like "I want that target gone" or "Cover us while we get out of here" or whatever. The JTAC uses airpower to meet the Ground Commander's intent. Now I'm not saying the in-game JTAC is particularly good at the job. But without specific tasks, targets will be assigned in I don't even know which order. And unless an air defense is the assigned target, it may come up behind an unarmed vehicle. If you want more fine control, you can assign individual targets and also target marking methods to the JTAC using the advanced waypoint actions and the FAC task, if memory serves. ================= Edited September 3, 2021 by Ramstein ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind G.Skill 64 GB Ram, 2TB SSD EVGA Nvidia RTX 2080-TI (trying to hang on for a bit longer) 55" Sony OLED TV, Oculus VR Link to comment Share on other sites More sharing options...
Tholozor Posted September 3, 2021 Share Posted September 3, 2021 (edited) JTAC issues are not an inherent problem with the Hornet, this belongs in the General section for DCS. Servers using a custom script also don't have much relevance to the baseline JTAC process (depending on what script it is), you'd have to take the issue up with whomever wrote the script. Edited September 3, 2021 by Tholozor REAPER 51 | Tholozor VFA-136 (c.2007): https://www.digitalcombatsimulator.com/en/files/3305981/ Arleigh Burke Destroyer Pack (2020): https://www.digitalcombatsimulator.com/en/files/3313752/ Link to comment Share on other sites More sharing options...
Ramstein Posted September 4, 2021 Author Share Posted September 4, 2021 (edited) 6 hours ago, Tholozor said: JTAC issues are not an inherent problem with the Hornet, this belongs in the General section for DCS. Servers using a custom script also don't have much relevance to the baseline JTAC process (depending on what script it is), you'd have to take the issue up with whomever wrote the script. yes, Jtac is not just for Hornet, wasn't sure where the question should asked,, since I wa inthe the F-18, Posted in F-18. maybe put question in Combined Arms. I don't know if it an issue with the script and settings in the setting for the map with Jtac. Am hoping soemone will know... Edited September 4, 2021 by Ramstein ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind G.Skill 64 GB Ram, 2TB SSD EVGA Nvidia RTX 2080-TI (trying to hang on for a bit longer) 55" Sony OLED TV, Oculus VR Link to comment Share on other sites More sharing options...
Ramstein Posted September 5, 2021 Author Share Posted September 5, 2021 I went into the Jtac in mission builder on the mission map, and asked it to lite the tanks, each as a group. And then flew the mission and reset the target lock and i then would proceed with the next tank, I would then lock, and then the next, the next, etc... (my mind went blank with the exact command.. with the 'C' key.. with the maverick search and lock) ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind G.Skill 64 GB Ram, 2TB SSD EVGA Nvidia RTX 2080-TI (trying to hang on for a bit longer) 55" Sony OLED TV, Oculus VR Link to comment Share on other sites More sharing options...
Recommended Posts