MustangSally Posted June 19, 2022 Share Posted June 19, 2022 Sorry, you have me confused. In Simappro you will have no throttle input from the aft stop to idle cutoff Ryzen 9 7950X3D - MSI MAG X670E TomaHawk MB, ASUS ROG Ryujin III 360 AIO 64gig Corsair DDR5@6000, Gigabyte GeForce RTX 4090 AORUS Winwing Super Taurus, Orion2, TO / Combat panels, Collective with Topgun MIP Winwing Skywalker pedals, NLR Boeing Mil Edition Simpit, Trackir Link to comment Share on other sites More sharing options...
Paladin1cd Posted June 19, 2022 Author Share Posted June 19, 2022 8 hours ago, Phantom711 said: Well...I don`t see that I said anything different really. Even though there is still a tiny bit of physical travel from IDLE till the aft backstop and the shut-off keybind is not pressed until I reach the full aft position. Anyways...the important part of the massege was, that my throttle shows no axis input at IDLE (in SimAppPro). This unfortunately seems to be the physical travel is after you pitch up the throttle to get it back into cutoff and its hard to go to idle and not kill the engine. nullThis might help? When pulled back to the idle position you notice it still has throttle put in. Link to comment Share on other sites More sharing options...
Paladin1cd Posted June 19, 2022 Author Share Posted June 19, 2022 On 6/18/2022 at 10:28 AM, Phantom711 said: again: you need to do the calibration in SimAppPro from IDLE to MIL and MAX AB. The throttle will then „consider“ the IDLE position as the „lowest“ position. have you done that? I just did this again and it still gives me the result from the screenshot. Link to comment Share on other sites More sharing options...
MustangSally Posted June 20, 2022 Share Posted June 20, 2022 Are you sure that you have calibrated correctly?? Here's a short vid I made on the correct procedure.... Ryzen 9 7950X3D - MSI MAG X670E TomaHawk MB, ASUS ROG Ryujin III 360 AIO 64gig Corsair DDR5@6000, Gigabyte GeForce RTX 4090 AORUS Winwing Super Taurus, Orion2, TO / Combat panels, Collective with Topgun MIP Winwing Skywalker pedals, NLR Boeing Mil Edition Simpit, Trackir Link to comment Share on other sites More sharing options...
Paladin1cd Posted June 20, 2022 Author Share Posted June 20, 2022 Ok, I finally got it sorted. However, doing so now all my scalable items like my radar ant elev and my dial (the slider below slider) suddenly have three positions only, but they are not in the three position mode. I tried to calibrate them and they keep jumping to either end or the middle. 51 minutes ago, MustangSally said: Are you sure that you have calibrated correctly?? Here's a short vid I made on the correct procedure.... Lovely video, thank you. So... The problem was which axis. I wasn't calibrating the correct axis. SMH. Now that I know how to figure out which axis is what I've got the new problem as I was going through them all to calibrate and now well... That video would have REALLY helped me the other day lol. Thank you! Link to comment Share on other sites More sharing options...
Phantom711 Posted June 20, 2022 Share Posted June 20, 2022 (edited) vor 13 Stunden schrieb MustangSally: Sorry, you have me confused. In Simappro you will have no throttle input from the aft stop to idle cutoff Yes…because you and me have calibrated our throttles that way. But as far as I know, the throttle is capable of providing input all the way from the backstop to „full AB“. Of course for us this would be unwanted, but people might want to use the throttle for other sims/games, that don‘t even support that feature (idle detent/shut-off) or don‘t need it (i.e.: space sims). Edited June 20, 2022 by Phantom711 vCVW-17 is looking for Hornet and Tomcat pilots and RIOs. Join the vCVW-17 Discord. Link to comment Share on other sites More sharing options...
MustangSally Posted June 20, 2022 Share Posted June 20, 2022 1 hour ago, Phantom711 said: Yes…because you and me have calibrated our throttles that way. But as far as I know, the throttle is capable of providing input all the way from the backstop to „full AB“. Of course for us this would be unwanted, but people might want to use the throttle for other sims/games, that don‘t even support that feature (idle detent/shut-off) or don‘t need it (i.e.: space sims). Cannot be done...just move it out of the detent. There is no throttle input between rear stop and Idle/off! Ryzen 9 7950X3D - MSI MAG X670E TomaHawk MB, ASUS ROG Ryujin III 360 AIO 64gig Corsair DDR5@6000, Gigabyte GeForce RTX 4090 AORUS Winwing Super Taurus, Orion2, TO / Combat panels, Collective with Topgun MIP Winwing Skywalker pedals, NLR Boeing Mil Edition Simpit, Trackir Link to comment Share on other sites More sharing options...
Phantom711 Posted June 20, 2022 Share Posted June 20, 2022 vor einer Stunde schrieb MustangSally: Cannot be done...just move it out of the detent. There is no throttle input between rear stop and Idle/off! Sorry...you are right. Just restored factory defaults to check it out. Didn`t expect this. vCVW-17 is looking for Hornet and Tomcat pilots and RIOs. Join the vCVW-17 Discord. Link to comment Share on other sites More sharing options...
Paladin1cd Posted June 21, 2022 Author Share Posted June 21, 2022 I also tried factory defaults and the bottom slider is stuck in three position mode but isn’t if you take my meaning. Along with the radar elevation. What do I do with that now? As it is I can’t work the radar at all and I don’t know what I could have done. In windows it shows the both of them acting incrementally as expected. Link to comment Share on other sites More sharing options...
MustangSally Posted June 21, 2022 Share Posted June 21, 2022 have you tried changing the mode using the 'Switch Mode' menu? Ryzen 9 7950X3D - MSI MAG X670E TomaHawk MB, ASUS ROG Ryujin III 360 AIO 64gig Corsair DDR5@6000, Gigabyte GeForce RTX 4090 AORUS Winwing Super Taurus, Orion2, TO / Combat panels, Collective with Topgun MIP Winwing Skywalker pedals, NLR Boeing Mil Edition Simpit, Trackir Link to comment Share on other sites More sharing options...
Paladin1cd Posted June 23, 2022 Author Share Posted June 23, 2022 The tab next to the slider is not showing buttons like when it is in that mode. It shows like a slider, which is what has me floored on that one. It was working just fine and now…. Not so much. It’s not useable at all because the antenna elevation is uncontrollable. Link to comment Share on other sites More sharing options...
Paladin1cd Posted June 28, 2022 Author Share Posted June 28, 2022 I finally got everything running. I wanted to thank EVERYONE for their input and support. Very much appreciated after spending hundreds of dollars and being stuck. Thanks a bunch. 1 Link to comment Share on other sites More sharing options...
Recommended Posts