Home Fries Posted April 2, 2022 Author Share Posted April 2, 2022 41 minutes ago, Rangoon said: Perhaps I've messed something up on configuration, but I think there may be something wrong with the UH-1H profile and VAICOM PRO. I am using Easy Comms just to try and eliminate as many variables as possible, but it was happening even with Easy Comms off. I also have Realistic Helicopter 2-stage Radio Trigger disabled (set to 0, per default). My Global - Communications settings are: VAICOM PRO 1, SRS 0, SR PTT Common 0, TS as DX 1, CommState Allow 1, Comm Menu by station 0, Chatter 1, AI RIO 1, TX5 Delay KBDelay, SR Overlay 1. Here's what I see: Throttle PTT Common Up: VoiceAttack shows TX1 press (release upon release), VAICOM Pro flashes TX1 SEL/AUTO and displays XMIT while held, Right MFD LED 1 illuminates while held. VoiceAttack and DCS respond to voice input. So this seems to work as expected in every regard. Throttle PTT Common Down: VoiceAttack shows TX5 press (release upon release), VAICOM PRO does not respond, Right MFD LED 2 illuminates while held. It's labeled PTT Common, so I assumed this should do the same thing as pressing it up. DCS does not respond to voice input, but VoiceAttack acknowledges in red text and says "...currently disabled for this session and was not executed." Throttle PTT Common Center Press: VoiceAttack shows TX4 press (release upon release), VAICOM PRO does not respond, Right MFD LED 1 illuminates while held. It's also labeled PTT Common. It's odd that the LED behavior changes again here. DCS does not respond to voice input, but VoiceAttack acknowledges in red text and says "...currently disabled for this session and was not executed." Trigger Stage 1: VoiceAttack shows TX5 press (release upon release), VAICOM PRO does not respond, neither Right MFD LED illuminates. DCS does not respond to voice input, but VoiceAttack acknowledges in red text and says "...currently disabled for this session and was not executed." Trigger Stage 2: VoiceAttack shows TX5 and TX1 press (release upon release), VAICOM Pro flashes TX1 SEL/AUTO and displays XMIT while held, neither Right MFD LED illuminates. VoiceAttack and DCS respond to voice input. So this seems to work, though it's odd about the LED. The other thing about Trigger Stage 2 is that you have to move slowly through 1 to 2. If you quickly full press to Stage 2, you get a different behavior: Trigger Stage 2 fast press: VoiceAttack shows TX5 and TX1 press (release upon release), VAICOM Pro flashes TX1 SEL/AUTO but only briefly flashes XMIT, neither Right MFD LED illuminates. DCS does not respond to voice input, but VoiceAttack acknowledges in red text and says "...currently disabled for this session and was not executed." Any idea what is going on here? All I'm doing is loading up an Instant Action mission on Caucasus: "Free Flight" where radios are tuned by default to Tbilisi and responds when the PTT is working. It's been a while since I've reviewed the Huey profile, and something may have changed with the settings. I'll take a look at it. 7 hours ago, papymaj5 said: Server is down again. I was just able to update. Is it still down on your end? 1 -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
Rangoon Posted April 3, 2022 Share Posted April 3, 2022 Also in the Huey, S2 Weapons Release Button is toggling VAICOM PRO's Chatter extension. It's set to Joystick 1 Button 2 in the VoiceAttack VAICOM PRO profile. I didn't see anything in the setup guide or other documentation about modifying this. I assume the button assignment should just be disabled in the profile, but it made me wonder if that meant my TARGET DCS PTT Import didn't work correctly. I don't see an entry for Chatter in the .vap file. In the setup guide, it says "...Chatter has been changed to R_CTL+L_ALT+V to prevent direct entry of numbers from also inadvertently toggling the Chatter function." The keyboard shortcut in my profile is 0 (zero). I'll change mine to that manually for now. Maybe that entry slipped through the cracks at some point and simply needs to be re-added to the .vap? Link to comment Share on other sites More sharing options...
e33et Posted April 11, 2022 Share Posted April 11, 2022 How can I testrun this without being forced to use TrackIR/Head Tracking software or VR? I'm stuck at error line 167 at DCS_World.tmc. I've tried to change the value in CTS software to not use TrackIR/Head Tracking software or VR but still unable to run it! Kind regards /e33et Link to comment Share on other sites More sharing options...
e33et Posted April 13, 2022 Share Posted April 13, 2022 Compile Error:Symbol not found: TrackIR in DCS_World.tmc at line 167 Link to comment Share on other sites More sharing options...
llorensan Posted May 2, 2022 Share Posted May 2, 2022 On 4/13/2022 at 9:30 PM, e33et said: Compile Error:Symbol not found: TrackIR in DCS_World.tmc at line 167 Same error for me Link to comment Share on other sites More sharing options...
Home Fries Posted May 2, 2022 Author Share Posted May 2, 2022 4 hours ago, llorensan said: Same error for me On 4/13/2022 at 3:30 PM, e33et said: Compile Error:Symbol not found: TrackIR in DCS_World.tmc at line 167 Could you guys please post your dcs_world.tmc files. -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 2, 2022 Share Posted May 2, 2022 36 minutes ago, Home Fries said: Could you guys please post your dcs_world.tmc files. Here is mine DCS_World.tmc Link to comment Share on other sites More sharing options...
Home Fries Posted May 18, 2022 Author Share Posted May 18, 2022 (edited) On 5/2/2022 at 10:37 AM, llorensan said: Here is mine DCS_World.tmc 23.35 kB · 3 downloads Sorry I took so long to get back to you. It looks like most of the values were not placed in their sections. The order of some of the values is important. Did you build the profile using the EXE? If so, try archiving your CTS.dat then removing it from your CTS folder. See if rebuilding your data file will fix it. Edited May 19, 2022 by Home Fries -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 20, 2022 Share Posted May 20, 2022 On 5/18/2022 at 11:05 PM, Home Fries said: Sorry I took so long to get back to you. It looks like most of the values were not placed in their sections. The order of some of the values is important. Did you build the profile using the EXE? If so, try archiving your CTS.dat then removing it from your CTS folder. See if rebuilding your data file will fix it. Unfortunately it doesn't work. I have uninstalled the whole app and installed a fresh one. Unlucky. I have found a wild solution by altering my dcs_world.tmc by shifting a whole block of int declarations from the end, to the beginning of the script. This allows me to continue using your CTS (with minor mapping issues). Don't worry. Only if a larger number of cases appear. Greetings, Lorenzo Link to comment Share on other sites More sharing options...
Home Fries Posted May 23, 2022 Author Share Posted May 23, 2022 On 5/20/2022 at 10:58 AM, llorensan said: Unfortunately it doesn't work. I have uninstalled the whole app and installed a fresh one. Unlucky. I have found a wild solution by altering my dcs_world.tmc by shifting a whole block of int declarations from the end, to the beginning of the script. This allows me to continue using your CTS (with minor mapping issues). Don't worry. Only if a larger number of cases appear. Greetings, Lorenzo I'm curious to hear what happens if you do try to use the EXE to build the file. Are you getting runtime errors with the script? -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 23, 2022 Share Posted May 23, 2022 1 hour ago, Home Fries said: I'm curious to hear what happens if you do try to use the EXE to build the file. Are you getting runtime errors with the script? okay delete my cts.dat delete my DCS_World.tmc run CTS.exe to make it easy I select only A10C Warthog all VALUES by default Settings A10C, A10C BUILD SCRIPT EXECUTE THE SCRIPT, and the evil mistake: Compile Error: Symbol not found: TrackIR in DCS_World.tmc at line 167 Thanks for your attention Lorenzo Link to comment Share on other sites More sharing options...
Home Fries Posted May 24, 2022 Author Share Posted May 24, 2022 Please send me that dcs_world.tmc -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 24, 2022 Share Posted May 24, 2022 13 hours ago, Home Fries said: Please send me that dcs_world.tmc Hi Here it is Lorenzo DCS_World.tmc Link to comment Share on other sites More sharing options...
Home Fries Posted May 24, 2022 Author Share Posted May 24, 2022 15 minutes ago, llorensan said: Hi Here it is Lorenzo This version also had the variables at the end. Does the compiler not properly put them in their sections? Again, order matters because some values are dependent on predecessors. -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 24, 2022 Share Posted May 24, 2022 27 minutes ago, Home Fries said: This version also had the variables at the end. Does the compiler not properly put them in their sections? Again, order matters because some values are dependent on predecessors. Hi Yes, it is the compiler that generates my DCS_world.tmc There is no manual modification on my part. It is evident that there is something in my installation that generates the disordered DCS. One possibility is my version of TARGET which is the latest. Specifically 3.0.21.910. Greetings, Lorenzo Link to comment Share on other sites More sharing options...
Home Fries Posted May 24, 2022 Author Share Posted May 24, 2022 Building dcs_world.tmc is strictly the job of the EXE using a MS Access database. The version of TARGET should have nothing to do with it. Try deleting cts.db again, then run the installer and do a Full Install to overwrite the old database. Then see if that fixes the issue. -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 24, 2022 Share Posted May 24, 2022 2 hours ago, Home Fries said: Building dcs_world.tmc is strictly the job of the EXE using a MS Access database. The version of TARGET should have nothing to do with it. Try deleting cts.db again, then run the installer and do a Full Install to overwrite the old database. Then see if that fixes the issue. HI Unlucky In fact I have completely deleted the Target profiles folder and installed a completely new CTS. Same result. I'm sorry Lorenzo Link to comment Share on other sites More sharing options...
Home Fries Posted May 29, 2022 Author Share Posted May 29, 2022 Version 2.63c Hotfix 3 released for DCS 2.7.14.24228. Change Log: Compatibility updates for DCS 2.7.14 F-14: updated emergency wing sweep functionality Converted TID functions from array to cycle Updated bindings since 2.63b: F-14 Updated SnapViews since 2.63: None Updated Custom Luas since 2.63b: AV-8B, F-14 1 1 -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
Home Fries Posted May 31, 2022 Author Share Posted May 31, 2022 (edited) On 5/24/2022 at 2:33 PM, llorensan said: HI Unlucky In fact I have completely deleted the Target profiles folder and installed a completely new CTS. Same result. I'm sorry Lorenzo The only other thing I can think of is to install to a completely different path, try again, and run the profile from the CTS EXE itself. If you still have issues, please pass me the dcs_world.tmc from the new folder (just to make sure it's not a legacy file somewhere). CTS doesn't use any registry entries, and it generates its own launcher batch file based on the path it detects. Not sure what else it could be. Edited May 31, 2022 by Home Fries -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted May 31, 2022 Share Posted May 31, 2022 4 hours ago, Home Fries said: The only other thing I can think of is to install to a completely different path, try again, and run the profile from the CTS EXE itself. If you still have issues, please pass me the dcs_world.tmc from the new folder (just to make sure it's not a legacy file somewhere). CTS doesn't use any registry entries, and it generates its own launcher batch file based on the path it detects. Not sure what else it could be. Hi No luck Removed installed CTS Install a fresh CTS in a folder c:\Fries (sorry) Execute CTS.exe Select only F16C module Default all values Settings F16C, F16C Build script Execute the script The error is slightly diferent: Compile Error: Symbol not found: Custom_Master_LUA_F14 in DCS_World.tmc at line 157 attaching the file DCS_World.tmc untouched Thank you Lorenzo DCS_World.tmc Link to comment Share on other sites More sharing options...
Home Fries Posted June 1, 2022 Author Share Posted June 1, 2022 (edited) 8 hours ago, llorensan said: Hi No luck <...> Thank you I can't fathom what it could be. I'll ask the GUI developer if he has any ideas. EDIT: What Unicode country are you using and what language is your OS? Edited June 1, 2022 by Home Fries -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted June 1, 2022 Share Posted June 1, 2022 12 hours ago, Home Fries said: I can't fathom what it could be. I'll ask the GUI developer if he has any ideas. EDIT: What Unicode country are you using and what language is your OS? Hi My unicode country is ES and my language is spanish. I have changed to english us (also installed) and the error persists. I have to explain that I am a former user of your CTS. It has always worked fine for me. It was NOT a CTS update that caused the error. It has been some Windows update (11) or other software that I have installed that caused the problem. Having found a workaround, I feel bad about causing so much trouble when I think my installation is to blame. Thanks for your efforts, Lorenzo Link to comment Share on other sites More sharing options...
Home Fries Posted June 1, 2022 Author Share Posted June 1, 2022 45 minutes ago, llorensan said: Hi My unicode country is ES and my language is spanish. I have changed to english us (also installed) and the error persists. I have to explain that I am a former user of your CTS. It has always worked fine for me. It was NOT a CTS update that caused the error. It has been some Windows update (11) or other software that I have installed that caused the problem. Having found a workaround, I feel bad about causing so much trouble when I think my installation is to blame. Thanks for your efforts, Lorenzo No problem, Lorenzo. I'm glad it is now working for you. I'm curious to hear your workaround so I may put it in the instructions. -Home Fries My DCS Files and Skins My DCS TARGET Profile for Cougar or Warthog and MFDs F-14B LANTIRN Guide Link to comment Share on other sites More sharing options...
llorensan Posted June 1, 2022 Share Posted June 1, 2022 1 hour ago, Home Fries said: No problem, Lorenzo. I'm glad it is now working for you. I'm curious to hear your workaround so I may put it in the instructions. Hi, Sorry but it's a bummer. I manually edit my DCS_world.tmc by cutting out the entire block of INT statements from the bottom of the script and pasting them immediately before the // Constants (should not be changed) block. The script runs without errors and, although I haven't done a full check, all the functions I use work fine (so far F16 C). Cheers, Lorenzo Link to comment Share on other sites More sharing options...
lvnona69 Posted June 7, 2022 Share Posted June 7, 2022 Hello! I noticed F18 control from DOCS Image for Warthog and MFD is not matching. From Image Boat Switch supposed to me Countermeasures but on my boat switch from your profile is AA/ AG. 1 MFD Top right up and down switch supposed to be for AA/AG but its something else (i think countermeasure switch) Is that normal and image just hasnt been updated or am i doing something wrong? Other planes looks like no issue. Thanks, Norm Link to comment Share on other sites More sharing options...
Recommended Posts