nomis

Gentlemen One thing about this profile is that it's not really for the x52 pro or non-pro. It is a profile for DCS, meaning all its changes are done inside dcs key bindings editor. Only the first step is done with saitek programming software (removing the shift states). That being said, i think it's just a matter of loading the lua into dcs and click your joystick buttons. Compare the actions being shown in the key bindings editor with those in the diagram provided. One very important thing: this profile didn't work out of the box for me. If you go a few posts back you'll find one where i explain what i had to do to get it to work. You guys go ahead and try. I think it should work with the x52 pro with little or no adaptation besides the one i mentioned in that earlier post.

You summoned the dead!! When you open the x52 programming software you probably see 6 columns. 3 for the normal modes and 3 for normal modes plus pinkie. These last 3 are shifted states. You need to remove them because later you'll set the pinkie as a modifier inside DCS controller configuration. You may also need to edit the provided lua file so that the controller ID matches your controller ID (I explained this a few posts back). Hope that helps. Back to the grave now.

Ok, found the problem. Each key assignment has an ID inside de .lua file. For example: "Gun Trigger - SECOND DETENT (Press to shoot)" has ID "d3002pnilu3002cd38vd1vpnilvu0" This was the ID found on the file from the OP. What i did was entering the sim and reset the X-52 column to defaults to have a really fresh start. Then, i set the button 1 to "Gun Trigger - SECOND DETENT (Press to shoot)" and saved as a profile. When i compared the IDs on the original file with that from the file i saved, i noticied there was a difference in IDs: Original (OP file): d3002pnilu3002cd38vd1vpnilvu0 My file: d3002pnilu3002cd13vd1vpnilvu0 See? cd38 and cd13. Then it was just a matter of using notepad++ to replace "cd38" with "cd13" and the profile loaded as expected. NOTE: you´ll probably find IDs with other terminations but don´t worry. They'll all have the same difference. NOTE 2: Find YOUR difference by using the method above. In my case it as a change from "cd38" to "cd13". Yours might be a different one. Hope that helps :)

Upon further investigation, it appears that SOME of the keystrokes are indeed loaded but misses most of them.

Thanks for the reply, HiJack. Well, i´m not sure if i did things the way you said so...but it didn´t work. I entered the sim and could get what i think is the controller ID by double-clicking the X52 title cell. I got: Saitek X52 Flight Control System {D5201950-CC9A-11e7-8001-444553540000} So i made a change to an axis (added a deadzone) and saved it as a profile. The file name was "test.diff.lua" (no ID in the name). I tried adding that first ID (D5201950-CC9A-11e7-8001-444553540000) to the filename of the profile i downloaded from the first post, like this: DCS FA-18C X52 Profile.{D5201950-CC9A-11e7-8001-444553540000}.diff.lua Didn´t work.... I´m on DCS World version 2.5.3

Hi all I´m having the same issue as Orac. When i try to load the profile, nothing shows up at the X-52 column. The shiftstates are clean and i only have 3 "pure" saitek X-52 modes. I´m loading the X-52 profile before entering the sim, as done with any other game. The only issue is when hitting any cell under the X-52 column so that the load profile button gets enabled and then loading the .lua file provided, nothing appears to be mapped... Any help? Thx!

Android version in sight?