maciusx

PROBLEM SOLVED I dont have activated INS+GPS. I was suffering from "drifting". thank you Mike_Romeo (discord help channel) from your help!

Hello, im having problems using the APROX mode. The ILS aprox course doesnt match with the real position of the runway (airport) in the map and the (52) icon of the airport its slighty offset to the right in the MFD compared to the real in the world. The magtenic variation its automatically set (06E) in the aprox/tacan page. The map tested is Caucassus with Trough the inferno Single Player mission Here is a picture This is another picture showing were is the "box" (waypoint) in the hud

Hi! Thank you Deka for allowing us to change the speed value of the cursors in the SPECIAL configuration page of the aircraft. The default speed is to high (for me) and not all of us have analog sticks to control the movement of the cursor in our hotas. The thing is no matter what setting you choose, the Y (vertical) movement of the cursor (At least in the MFD Radar mode) is faster than the X (horizontal) movement. I know this is not an important bug but, can you please make the speed movement equal on vertical and horizontal axis? For better fine adjustments. The problem is more noticeable with higher value numbers thank you very much. Wonderful plane

Yeah, maybe it’s time to get rid of being lazy and start doing manual lasing hahah. I was playing “through the inferno” and having a blast bombing defenseless tanks and trucks and creating waypoints via CDU with the jtac coordinates. So much fun! Then experimentating with different laser codes and profiles to not get my bombs crazy with two same lasers (the jtac one and my own plane) because, can I ask, what is the range of the gbu12 in one area to not get confused for another same laser code? If I’m bombing some trucks that are, let’s say, 50 meters next each other, can the laser of the jtac interfiere with mine? (Assuming I’m using the same) That’s why I was testing with profiles, different codes and such. I have the impression that if im bombing a group of vehicles with same jtac code (1688) sometimes the bomb goes to another vehicle. Or maybe it’s placebo. And, it’s me or the gbu 54/38 it’s not very accurate using coordinates? I create the waypoint and making it steerpoint via coordinates of the jtac, but I’m not getting direct hits dropping them in range with ccrp. The hits it’s offset maybe 20 or more meters. I read in the 2.5 subforum that maybe it’s a bug with calculations but Im not sure it’s me or it’s a bug. I think I’m doing well but not sure. With laser bombs I have not problems

Thanks for the response After some testing, I think the better “solution” it’s to create one profile , the one more complex for own purpose, for example GBU12/AL (auto lasing) and vía hud or with the rocker select it for own laser employment, making sure that the one we are going to drop it’s in the correct pylon ( in my case pylon 8 ). This way we avoid unnecesary cycles through too much profiles and pylons. If we want to use the one in the pylon 4, for jtac laser code, simply select it via click on the osb in the dsms page. This way the pylon it’s selected with the default settings (we want autolase off) and when bombing check in the hud M/GBU (manual). this way we declutter some unnecesary cycles between profiles, but the downside it’s we are utilizing default bomb settings for the pylon 4. I know you can simply ignore the “mismatch laser code” warning and the “tgp laser fail” if we drope the jtac bomb using own profiles. It’s going to hit, but I like to avoid those messages. Greetings

Hi!! I have loaded in the a10c this weapons pylon 4: 3xgbu12, laser code 1644 (for ground JTAC) pylon 8: 3xgbu12, laser code 1688 And i would like to create two profiles: profile 1 to use my own laser 1688: Auto lasing, minimum altitude 1000, laser time 8 sec, etc profile 2,to use with jtac: Default settings, autolase off, etc Its is possible to assign profile 1 to pylon 8, and profile 2 to pylon 4, and cycle between each pylon each time with dms right, left? Because the thing is, creating this two profiles is easy, but when i want to cycle between profiles, it cyles between two pylons each time for each profile. Each time i press cycle: profile 1 (pylon 4) profile 1 (pylon 8 ) profile 2 (pylon 4) profile 2 (pylon 8 ) And i would like to cycle like this: profile 1 (pylon 8 ) profile 2 (pylon 4) It is possible? I know i can deactivate profile 1 if am bombing with JTAC, but the pylon 8 remains active, and im only using the 4 for jtac, and adds extra work on the OBS. The idea is to cycle between pylons only. Assign profiles for individual pylons, and get rid of the "laser mismatch" warning each time i cycle through the pylon 4 with the "autolase on" profile 1 thanks