DocSigma Posted December 7, 2010 Posted December 7, 2010 I've been running different JTAC scenarios. First one I engaged infantry... all wen pretty smooth.. i was tasked to engage with CBU-97's, but the jfac didn't mark with smoke with or anything and with out a TGP on board the best I could do was Hook the target location and make it SPI then dropped 2x CPU-97's (CCIP). I killed a couple of them but also took out some of my guys.. anyway it went as planned. HOwever, was trying a few guided bomb directed attacks. Confirmed 9 line with jtac, made the laser on call. Called the spot.. all looking good.. had the tgp on my target but as the then the jtac called abort. I tried a couple of times with same outcome. anybody know why that is? Also, I've set the jtac to group activate at a trigger.. and it does but i'm not getting the message that I made in the mission editor in the trigger command window. I'm forced to radio the JTAC myself. I have the JTAC, aggressors, and message from the Jtac activate all tied to a once trigger command. Is this okay, or do I have to set up 3 separate "once" instances for each AI action? Thanks for any help> Ryzen9 5800X3D, Gigabyte Aorus X570 Elite, 32Gb Gskill Trident DDR4 3600 CL16, Samsung 990 Pr0 1Tb Nvme Gen4, Evo860 1Tb 2.5 SSD and Team 1Tb 2.5 SSD, MSI Suprim X RTX4090 , Corsair h115i Platinum AIO, NZXT H710i case, Seasonic Focus 850W psu, Gigabyte Aorus AD27QHD Gsync 1ms IPS 2k monitor 144Mhz, Track ir4, VKB Gunfighter Ultimate w/extension, Virpil T50 CM3 Throttle, Saitek terrible pedals, RiftS
nomdeplume Posted December 7, 2010 Posted December 7, 2010 Called the spot.. all looking good.. had the tgp on my target but as the then the jtac called abort. I tried a couple of times with same outcome. anybody know why that is? Did they request you run in from a particular direction? Did you call 'contact the mark' etc. on your way in? Not always required e.g. for type 3, but it's all I can think of off-hand. Well, that and "WIP". :) Also, I've set the jtac to group activate at a trigger.. and it does but i'm not getting the message that I made in the mission editor in the trigger command window. I'm forced to radio the JTAC myself. I don't think there's anyway to avoid having to check-in with the JTAC to start the process. What exactly did you have set up? If you're using one of the 'message' actions it'll appear in the top-right corner, not the top-left where the in-game communications appear.
DocSigma Posted December 7, 2010 Author Posted December 7, 2010 I think my problem was with the lgb run that I didn't let the laser lock to their designated target but set the left target as soi. Ryzen9 5800X3D, Gigabyte Aorus X570 Elite, 32Gb Gskill Trident DDR4 3600 CL16, Samsung 990 Pr0 1Tb Nvme Gen4, Evo860 1Tb 2.5 SSD and Team 1Tb 2.5 SSD, MSI Suprim X RTX4090 , Corsair h115i Platinum AIO, NZXT H710i case, Seasonic Focus 850W psu, Gigabyte Aorus AD27QHD Gsync 1ms IPS 2k monitor 144Mhz, Track ir4, VKB Gunfighter Ultimate w/extension, Virpil T50 CM3 Throttle, Saitek terrible pedals, RiftS
Recommended Posts