Doctor027 Posted May 13, 2016 Posted May 13, 2016 (edited) Hello everyone ! I meet one problem that is my m2000c cold start. I switch on the power but there are still some lights on on the panel and i can not start the engine , i have two pictures to show the matter. Anyone can help me ? The first picture is the time i just switch on the power, the second is i already switch on some switches of the engine. Edited May 13, 2016 by Doctor027
Darkbrotherhood7 Posted May 13, 2016 Posted May 13, 2016 (edited) Check the fuel cut-off button and the throttle position. Edited May 13, 2016 by Darkbrotherhood7 Mission: "To intercept and destroy aircraft and airborne missiles in all weather conditions in order to establish and maintain air superiority in a designated area. To deliver air-to-ground ordnance on time in any weather condition. And to provide tactical reconaissance imagery" - F-14 Tomcat Roll Call [sIGPIC][/sIGPIC]
Doctor027 Posted May 13, 2016 Author Posted May 13, 2016 Check the fuel cut-off button. Ok Thanks I will do it now .But where's that button?
Doctor027 Posted May 13, 2016 Author Posted May 13, 2016 Check the fuel cut-off button and the throttle position. I find it and switch it on,but the lights still on!
Azrayen Posted May 13, 2016 Posted May 13, 2016 A/ The lights remaining "On" on the alarm panel are normal because your engine is not started. B/ Your problem is that you can't start your engine => make both actions advised by Darkbrotherhood7, that is (in that order): --- 1/ ensure that your throttle axis is set to zero; use controls indicator if need be, the simulator may have a higher value than you actual physical axis; move the physical axis (your joystick/throtlle) to ensure synchronisation. --- 2/ as you have moved your throttle, you must reset the engine throttle to the "stop" position; to do that, press the "engine stop" red button next to the throttle. Then try again starting the engine :)
Doctor027 Posted May 13, 2016 Author Posted May 13, 2016 A/ The lights remaining "On" on the alarm panel are normal because your engine is not started. B/ Your problem is that you can't start your engine => make both actions advised by Darkbrotherhood7, that is (in that order): --- 1/ ensure that your throttle axis is set to zero; use controls indicator if need be, the simulator may have a higher value than you actual physical axis; move the physical axis (your joystick/throtlle) to ensure synchronisation. --- 2/ as you have moved your throttle, you must reset the engine throttle to the "stop" position; to do that, press the "engine stop" red button next to the throttle. Then try again starting the engine :) i saw some video of the cold start of M2000C ,when they switched on the power button the weapon's panel light will be on.buy mine the lights is off, you can the at the first picture. and my thtottle axis is 0
Azrayen Posted May 13, 2016 Posted May 13, 2016 Because video is old, was made before electric system was fully implemented. Now, many systems requiring AC power won't work until you either: - have the engine running (= alternators working) - or have the GPU On = = = = = = = Regarding your throttle, I can't tell. I know you're not the only one (many topics about this), and each time it was an issue with the throttle (ingame) not being zero. This is why I advise to double-check this.
Doctor027 Posted May 13, 2016 Author Posted May 13, 2016 Because video is old, was made before electric system was fully implemented. Now, many systems requiring AC power won't work until you either: - have the engine running (= alternators working) - or have the GPU On = = = = = = = Regarding your throttle, I can't tell. I know you're not the only one (many topics about this), and each time it was an issue with the throttle (ingame) not being zero. This is why I advise to double-check this. Thanks! your ways is right,now i can start it now!
Recommended Posts