B2Blain Posted January 15, 2017 Posted January 15, 2017 I created a detent in the throttle. But I can't seem to get the engines to military power at the detent stop. JOY_RZ is set as left throttle JOY_Z is set as the right throttle I tried to adjust the curvature - using this as a starting point. https://forums.eagle.ru/showthread.php?t=122496&highlight=afterburner+detent The best I could get was 76% power at the detent. In Falcon BMS you can set the detent within game, but there doesn't seem to be a similar option in DCS. Do I need to axis tune both the right and left throttle or just the left? Thanks!
B2Blain Posted January 16, 2017 Author Posted January 16, 2017 I've tried a number of things in game - adjusting saturation and implementing curvature. I also check slider on and off. It seems idle is at military power (68-74% -depending on settings). Nothing happens between the idle detent and military power (start of the afterburner detent) - no change in RPM. I am only able to move between idle and afterburner passed the afterburner detent. I have calibrated my throttle using TM's calibration tool. Is this an issue outside of the game - i.e. windows? Anyone have suggestions?
PiedDroit Posted January 16, 2017 Posted January 16, 2017 Not sure to understand... First, which aircraft are you trying to tune the detent for? Second, what do you mean by: It seems idle is at military power (68-74% -depending on settings).When throttle is idle, you get military power in game? Or vice versa? Nothing happens between the idle detent and military power (start of the afterburner detent) - no change in RPM. I am only able to move between idle and afterburner passed the afterburner detent.Do you mean that you move the throttle and in game, nothing happens between idle position to the detent? There is something seriously wrong with your throttle if that's the case :wassat: Normally to adjust the point where the detent is, you only need to set the axis to "slider" mode and adjust the curve. Also when doing the calibration, make sure to go past the the detent to the full range of the throttle. If it's obvious to you, perfect :)
B2Blain Posted January 16, 2017 Author Posted January 16, 2017 Not sure to understand... First, which aircraft are you trying to tune the detent for? Second, what do you mean by: When throttle is idle, you get military power in game? Or vice versa? Do you mean that you move the throttle and in game, nothing happens between idle position to the detent? There is something seriously wrong with your throttle if that's the case :wassat: Normally to adjust the point where the detent is, you only need to set the axis to "slider" mode and adjust the curve. Also when doing the calibration, make sure to go past the the detent to the full range of the throttle. If it's obvious to you, perfect :) I am playing F-15C in DCS World 2.0. Regarding your first question. FYI - I have installed the TM afterburner detent part so I need to lift the throttle physically over the hump in order to enable the afterburner. When the throttle is physically between idle detent and the afterburner detent - and I push toward the afterburner detent it has no affect on the engine RPM. Only when lift it over the detent does engine RPM start to increase. The thought that there was something wrong with the throttle did cross my mind. I will attempt to adjust the curve again. If I move the throttle while tuning the axis for the throttle is there anything that will indicate the location of the detent? Thanks, Blain
B2Blain Posted January 16, 2017 Author Posted January 16, 2017 I've not tried the TM calibration tools, try doing a windows calibration. As for matching up the detent. Start by finding where the afterburner starts, remember where the boxes on the bottom are. Next you need to find the position of your detent, that's here for me. Now you need to edit the curve in such a way that the black box which is the input the game uses, is just short of engaging the afterburner while the red box, which is the position of your axis, is in the position of your detent. While trying to keep it as linear as possible. You need to do this for both axis but it should be as simple as just writing down/screenshotting the user curve numbers. Thanks! So if the black box with red in the center the location of your afterburner detent?
B2Blain Posted January 16, 2017 Author Posted January 16, 2017 I think I may have figured it out. I usually just calibrate the HOTAS using TM's calibration tool. I decided to calibrate using the windows tool and I think that was the culprit. I now can adjust engine RPM between the idle detent and the afterburner detent. Thanks Vladinsky and PiedDroit for your suggestion!
PiedDroit Posted January 16, 2017 Posted January 16, 2017 I think I may have figured it out. I usually just calibrate the HOTAS using TM's calibration tool. I decided to calibrate using the windows tool and I think that was the culprit. I now can adjust engine RPM between the idle detent and the afterburner detent. Thanks Vladinsky and PiedDroit for your suggestion! Another problem bites the dust! :thumbup:
Recommended Posts