draken152 Posted October 11, 2017 Posted October 11, 2017 Hi All, I am currently working on gauges for my fw190D pit, but I am still missing Vid60 stepper motor for altimeter. A have already checked aliexpress, ebay and amazon but without success. I have done the same for X10 stepper motor as substitution but also with zero effect (even I dont know if this motor can be used for this purpouse)... Any advice where to buy this kind of staff???:helpsmilie::helpsmilie::helpsmilie: [sIGPIC][/sIGPIC] Building FW190D pit ,,To Dora with love" http://forums.eagle.ru/showthread.php?t=132743
ESA_Falke Posted October 11, 2017 Posted October 11, 2017 Why you dont use the X27 stepper motor? https://es.aliexpress.com/wholesale?catId=0&initiative_id=SB_20171011080613&SearchText=X27+stepper+motor
draken152 Posted October 11, 2017 Author Posted October 11, 2017 That is different kind of motor similar to VID29 so with 315° movement I have 10 of them for different gauges... For altimeter you need 360°(continuous) if you don't want to use gearbox… Like here https://forums.eagle.ru/showthread.php?t=145193&highlight=vid60 [sIGPIC][/sIGPIC] Building FW190D pit ,,To Dora with love" http://forums.eagle.ru/showthread.php?t=132743
fbfan64 Posted October 11, 2017 Posted October 11, 2017 It's a simple mod to make the x27 stepper run 360 degrees but you will have to implement your own switch to mark the reference position. Sent from my SAMSUNG-SM-G891A using Tapatalk My Simpit Project
draken152 Posted October 11, 2017 Author Posted October 11, 2017 OK thx I was not aware about this it can be my plan B, if I will be not able to obtain VID60:thumbup:. If you will be so kind you can share with us the way how to mod X27 (I have Vid 29 it should be the same) in between:pilotfly:. Still if somebody has Vid60 in his possession or know way how to obtain it, I will buy it … [sIGPIC][/sIGPIC] Building FW190D pit ,,To Dora with love" http://forums.eagle.ru/showthread.php?t=132743
fbfan64 Posted October 12, 2017 Posted October 12, 2017 Sorry I don't have any pictures handy but maybe my description is enough. Inside the motor, there is a groove that runs 315 degrees around. There is a small plastic peg that runs inside this groove. That is the only thing stopping it from rotating 360 degrees. With a small pair of cutters or hobby knife, carefully slice off the peg. Reassemble the case and it's good to go. Then you can use a small magnet attached to the pointer and a reed switch mounted on top of the motor case or just under the pointer to detect a reference position. Now you can rotate the motor full circle and use the reed switch to detect when it is at the reference position. (The reference position is just so that when you start up, you can get the pointer to a known position since you can't be sure where it was left the last time it powered off.) If you get to the point you are going to do this you can PM me if you need some more guidance. My Simpit Project
draken152 Posted October 13, 2017 Author Posted October 13, 2017 Found X10, but quiet expensive in my opinion http://www.inovauto.com/index.php/sei-x10-506.html#product_tabs_downloads [sIGPIC][/sIGPIC] Building FW190D pit ,,To Dora with love" http://forums.eagle.ru/showthread.php?t=132743
WhoMadeWho Posted October 13, 2017 Posted October 13, 2017 Same issue I'm looking for guidance as well for motors to use on my altimeter...
Recommended Posts