Alpha_Mo66

oh! that would make perfect sense.. My bad for dropping the ball like that. Thanks for clarifying though

@uboats not sure how you labeled the issue as "fixed", because the problem still persists. I'll be attaching another short TRK file soon.

Please view my trk file and emulate the step sequence I took until the issue occurs. I f you end up getting the same issue, then I believe it's good reason for Devs to investigate in the root cause of the issue. 1. Load module with GB-6-sfw 2. designate a ground target 3. launch GB-6 4. Adjust MSL Vol knob

The "dididi" warning is not an issue. I'm perfectly aware of its purpose. It's the audible warnings like "Fuel" and "Altitude, Altitude" that start playing without indication (master caution) and can't be turned off until you land. This only happens while you're airborne, with master switch armed, and after adjusting the MSL Volume knob. I'll attach another TRK file, but shorter this time for everyone to view. I'm also doing a slow repair to DCS while drafting this reply. Hopefully the repair would fix the issue Edited: Slow repair didn't fix the issue. Please watch the track up until the time I lock on ground target, launch the GB6-SFW and adjust the MSL Vol knob. @JG54_NF2 and @uboats Pretense_PersianGulf_5am-20231128-212339.trk dcs.log

Spot on!! You hit the nail directly on the head.. No warning light flashing, and the warning sounds never stop. This will continue throughout the track the minute I am airborne and rotate the MSL Volume knob while master arm switch set to on. However, the issue doesn't occur on the ground regardless of master arm switch's state.

I have lately been experiencing an issue whenever I adjust the MSL Volume knob midflight. It results in non-stop audible warnings going off and there's no way I am able to stop them. Surprisingly, the warning button does not flash when this happens. I recently noticed that it reproduces only when the Weapons Master switch is turned on. Irrespective of turning it back to safe and resetting the warning system by clicking the button, there is no way that I know of that silences the audible warnings. dcs.log Pretense_PersianGulf_5am-20231126-144651.trk

Lately I've been experiencing a weird bug whenever I adjust the MSL Volume knob midflight. The audible warning system goes insane and never stops giving me all programmed warnings "Bingo, Low Altitude, Pull up, etc." Can't say I am able to figure out a pattern for it to happen just. Seems to randomly kick in and mostly when the jet is airborne. Anyone else suffering from the same issue or is it a setting I need to tweak in the specials menu?

It worked for me without getting the error message.. Thanks for the fix @baltic_dragon

My guess is the update will only come into effect with the next DCS patch.. Best we get a confirmation from Baltic or ED in this case

Any update on resolving this issue? @baltic_dragon @BIGNEWY

Please try to fix this issue. I am seriously hooked on to this amazing campaign, and would hate to skip the mission. Replayed it 3 times so far with and without 3rd party mods installed. Can't wait to go through the other missions once resolved

"Reviving this old post:" Where can I obtain this profile? @Capt Zeenseems to have removed it from the downloads section of his website. The same goes for other FC3 modules, like the F15 and SU-27

Okkkk.. we are making progress. I am able to receive MFD overlays. However, they seem to be static on TSD page (RMFD) and WPN page (LMFD). Any suggestions on how i can turn them into interactive overlays?

Great work @Bunny Clark. Much appreciate your hard work and effort in making this happen. I downloaded/installed your profile as instructed. However, my MPD's are still not able to receive the exported overlays from DCS. Any ideas on what I may have done wrong during the installation process, or perhaps overlooked? Otherwise, all the buttons are functional and accessible, both in Pilot and CPG mode

Reviving this old thread, and hoping to get someone to help me out with my situation... I'm currently running a dual monitor setup. 3440x1440 center screen, and a 1920x1080 touch screen below center. Therefore, my combined resolution is 3440x2520. My problem with the control indicator box is that it gets hidden in the combined resolution and is not visible anymore in the bottom left corner of my center screen. I was hoping for someone to figure out the values needed to modify the lua file and place the indicator box in the desired location. I'm attaching an image of my display layout and marking out the desired location. My apologies in advance for my limited skills in all this tech-stuff. Any help i can get with this will be highly appreciated, as ED Support informed me it is not possible, even though I tried it myself and was able to locate it to the top left corner of center screen.