Allan Stark

Yes, I compiled psocdude and installed all dependencies and dev libs. /dev/ttyACM0 was present, when I connected Arduino to the USB. TX/RX Arduino LEDs light up when I run the psocdude, but then go out and I get this error. Do I need to connect the PCB to the USB as well?

@acidwise Yesterday I finally managed to try to reflash the PCB. I had an Arduino UNO controller and a Kali Linux laptop. Pin VCC (PCB) was connected to pin PWR/5V (Arduino UNO) and GND to the Arduino's GND next to the 5V pin. Unfortunately, I got the error "psocdude: stk500_recv(): programmer is not responding" when trying to backup, so I did not reflash. The PCB was completely removed from the throttle case, only the USB cable remained. I connected PCB to the Arduino and Arduino to my laptop. JST XH1.25 connectors turned out to be of poor quality and a couple fell apart when removing the cables, so I ordered new ones to replace. It's strange that Thrustmaster, with such thick metal of device, saves so much on conventional wiring...

@acidwise I'll probably try the flashing, because still have nothing to lose. I already have an Arduino Uno. If possible, please tell me the procedure (to which pins on the Arduino and PCB I need to connect cables, do I need to remove the PCB from the throttle, which Arduino libraries to use, etc.). Thank you very much for your help!

Unfortunately no. Windows Device Manager shows this device as: Unknown USB Device (Device Descriptor Request Failed) Windows has stopped this device because it has reported problems. (Code 43) A request for the USB device descriptor failed. I tried to connect this throttle to another PC with Win7 and USB2.0 ports, but got the same result with bootloader method.

@acidwise Thank you for the answer! Unfortunately I tried to use bootloader method many times on my PC with Windows 10 USB3.0 and USB2.0 ports as well as on my laptop with Win7. This did not help, apparently the loader is also damaged. It is strange that for this controller it is impossible to perform initial firmware flash via the USB port, but it is necessary to connect it with a cable to an external controller.

@acidwise Thank you for your researching work! I have some questions: Is it possible to reflash an existing CY8C24894-24LTXI chip or is it necessary to look for a replacement? How to determine that the chip is out of order and needs to be replaced? All 5 LEDs in the upper part of my HOTAS Throttle briefly light up when I connect the device to the USB. Is it possible to flash through the Arduino UNO or is it necessary to have a Leonardo or Pro Micro?

Ответил, что есть в наличии.

Да, спасибо, уже связался с ним.

Добрый вечер. У меня к сожалению такая же проблема. HOTAS Warthog Throttle был подключен к USB3.1 портам вместе с Warthog-овским джоем. Позавчера РУД перестал корректно определяться в системе, с точно такими же ошибками. При подключении РУДа к ПК кратковременно загораются верхние 5 светодиодов, после чего РУД видится в системе как неизвестное устройство: Unknown USB Device (Device Descriptor Request Failed) Windows has stopped this device because it has reported problems. (Code 43) A request for the USB device descriptor failed." Комплект проработал исправно почти ровно 3 года. Пытался восстановить через бутлоадер по мануалу из FAQ-а с сайта Трастмастера (путем зажатия пальцами двух кнопок и подключением к USB) как на оригинальной системе (Windows 10), так и на ноутбуке с 7-кой. Пробовал подключать в разные порты на материнках, в т.ч. USB2.0. К сожалению без результата... На всякий прозвонил USB кабель, хотя на нем нет мест перегиба. Пробовал писать в саппорт, молчат, да и не на гарантии он уже. Устройство можно выкидывать или есть надежда как-то оживить? Можно ли контроллер (судя по фото там Infineon CY8C24894-24L) прошить через USB или проблему можно решить только заменой платы? Есть ли возможность заказа платы либо починки в Киеве?