kmaultsby

Thank you

The wife gave me the ok to purchase a new monitor for flight sim. My Graphics card is RTX4070, I am looking for monitor between 32 and 42 inches. My budget is $500 or less.

Thank you, MAXsenna and mkdI2010, but I want to make sure I understand. When you say set turned off deadzones, we are not talking about Axis Tuning in control settings, correct? My other question is, what do you have your Axis Tuning settings?

In DCS in the Options window under the Special TAB for the F16, should the Pitch & Roll Axis Force Gradient be checked on or off. I am using the WINWING Orion2 ViperAce(EX) Joystick. This is the Non Force Feedback.

What is the keyboard command for Active Pause for the F16. Where find keyboard command list?

Hello all, I have the Legend MIP with all three MFD's. When flying the F16 I can raise the brightness on the left and right MFD'S with the brightness control, but for the HSI in night mission the display is dark. Do you have to set display brightness manually in SimApp Pro?

All a friend is looking for a good all around Throttle I ask him to joint the forum but I am asking this question for him. The aircraft he fly's F16 F18 and MSFS. Would this be a good Throttle for him?

Thanks

No, It is not for the force sensing. Let me give an example. Learning to do Air refueling and tried different settings and what is happening for pitch nose down is ok but nose up it is acting like have a dead zone compare to nose down. I have to give more input nose up and went it does move it is too much input. I did recalibrate, but still didn't help.

Sorry I don't know what happen, I thought I was in the WinWing forum. Dos Thank you very much. A lot of information. I am just using the regular F16 stick. " "Pitch & Roll Axes: Apply a negative curve between -4 to -15. This adjustment compensates for the Viper's hardcoded force-sensing curve, offering smoother and more precise control, particularly in the center zone. reddit.com+4reddit.com+4reddit.com+4" Is this just for the force sensing.?

Thank you very much for the advice and suggestions.

Looking for good starting control settings points for this joystick for the F16 in DCS. Axis, Saturation, dead zone. Any recommendation or suggestions is greatly appreciated.

Thanks for the info.

All need advice on a good starting point to set up the ViperAce Stick for the F-16. I am all over the place with formation flying and AA refueling. Advice on the Axis tuning.

Hello all, I am looking for advice and suggestion for programming my Hotas for FA-18. First, let me give some background. I first purchased the Winwing Viper MIP and the WINWING Orion2 HOTAS ViperAce setup for F16 and program all the controls in DCS. A few weeks ago I completed my setup bye adding another MFD and purchasing NavyAce UFC&HUD and the WINWING Orion2 StrikeAce EX Throttle Combo for FA-18 and F15. So basically I have Legend MIP with two throttles. Now I need to program controls for the FA-18. My question is in SimApp Pro you can download other creators Key Bindings, which some of them that I liked but were missing some control that I would like to add. My question is if I use one of the profiles and add my in DCS will it save the controls in DCS or will the Key Binding in SimApp pro override them or remove them? Or is there away I use one of the profiles input my addons in DCS and save it as my personal profile Key Bindings? I hope my questions make sense.

Do you know if most everyone is using 4x32 or 128?

I am trying to understand SimApp pro setup. I know DCS support 128 button mode but I also fly BMS. My question is if I understand correctly is I would have to set up SimApp Pro to 4X32 to setup my controls for BMS or any other sims, and then switch back to 128 button mode for DCS? Is that correct.

Ok, I have another question. With the VR headset on, how do you turn dials and switches in the cockpit? I have the WinWing ICP and MFD'S.

I see the price will be high. How about the Pimax Crystal Light vs Q3 pro?

Quest Pro at $900 is a little out of my budget. What is 5800x3d?

Thank you. You mention I may need to compromise on the settings, which component is the more the bottleneck, the CPU, Graphics card or both?

Hello all, I am new to this and just joint a squad and one of the pilots suggested I should switch to VR because I was having trouble seeing small objects on the ground trucks tanks etc. I have some questions. How do you do microphone and hear other pilots in multiplayer? I was thinking of purchasing the Meta Quest 3. Will my computer be ok to handle a VR setup. I am also using the WinWing MIP and ICP in my setup now. Any recommendations or suggestions? Computer specs below. Processor AMD Ryzen 7 7800X3D 8-Core Processor 4.20 GHz Installed RAM 32.0 GB (31.2 GB usable) System type 64-bit operating system, x64-based processor 32 GB RAM, 2Tb ssd, Edition Windows 11 Pro Version 23H2 Nvidia RTX 4070

What I did is just change out the CAMS. I am getting used to it. Feel more like Thrustmaster now with less center

On YouTube and some forums, I hear and see good and bad reviews. Mostly the bad is related to the setup in SimApp Pro. Do you own the force sensing?

Hello all, I am new to the Winwing equipment and have received a lot of help from others here. I am still a rookie flying the F16, and the Joystick felt light to me, so I ordered the CAM spring kit. I changed out the CAM so it would have less center play but made the joystick feel stiffer. This is okay, but now I am working on my air-to-air refueling, and the stiffer feel may not be a good idea. I would like to hear from others about the stick's play. Do you like it? If you didn't make any changes did you adjust the curve sensitivity a lot in A settings? Did you change out the CAMS, springs, or both?