bobd

I have the same problem also. Finally got my ticket answered, but didn't help. Back waiting again. :cry: BTW BS2 was activated. Norm how did you get it working ? Thanks

Good news I finally got it to start. It had nothing to do with reading the ******* manual, or flipping a sequence of switches, & levers. :glare: I did another download, uninstalled world then reinstalled world & p51. Must have had a bad install.

Thanks for all the help

Just got P-51 & can't get it to start in the training session. When I click on the start switch the engine won't crank. Some needles move a little, but that's all. I tried using the Home key also. Any idea ? Thanks,

Your best bet is go back to CH Hanger forum for help.

Nice work Peter :thumbup:

I have it now. Part my piloting, part axis for collective calibration. Too much, too fast. Thanks for all the suggestions. :thumbup:

Hi ShuRogal According to the manual, I should have it in auto ( notch) for normal operation. At IDLE mode are usually performed startup procedures and most of the systems functional tests. GOVERNOR FAIL is needed in case of failure of power turbine’s RPM governor to avoid engine (power turbine) overspeed. AUTO is the main mode during normal operation of the powerplant. All flights must be performed at this mode, except for specific emergencies. MAX mode is intended to ensure maximum power of one engine in case of failure of the other engine.

Ramp, or runway does the same. Played with page up/down works like it should. I can take off in idle, or govern with no warning beep.

Just getting back into BS (now BS2) after a long time. Either the game is confused, or I lost my mind. I can't take off, or gain altitude with the throttle levers in auto, or max without the rpm warning beeps going. Warning only stops by pushing down on the collective. :confused: Thanks for any help.

I was thinking BS2 1.1.1.1, but now I see not. Thanks again

Thanks cichlidfan, sorry should have said up to BS patch1.0.2. Any BS2 patches before BS patch1.0.2 ?

Could someone please advise me a clean reinstall BS1 with BS2 upgrade. These get a little confusing for me. Thanks,

I realize it's still a WIP. I always enjoyed MSFS with FF because of extra forces like touch down, ground rolling, & gear up bump, etc. Please consider these for your FF programing...it really adds to simming. Thanks,

Looking forward too this also!! :thumbup:

Thank you Peter, problem solved. Also got back some FPS that I was hoping for.

Both are set to native 3840 x 1024 & 1366 x 768. In game option is set to 3840 x 1792 _ = function(p) return p; end; name = _('Mine'); Description = 'Two monitor configuration'; Viewports = { Center = { x = 0; y = 0; width = 3840; height = 1792; viewDx = 0; viewDy = 0; aspect = 1.6; } } LEFT_MFCD = { x = 1300; y = 1092; width = 492; height = 492; } RIGHT_MFCD = { x = 2049; y = 1092; width = 492; height = 492; } UIMainView = Viewports.Center Thanks Peter

I have a small monitor below the main, with TH pack. If you look at my pic you can see the ADI, along with the MFD's. What do I need to do to remove the lower part of the panel in the small monitor? Hope this makes sense. Thanks for any help.

Hi Hanzales, That's fantastic news! :) Thank you... Standing by

Hi, saw your post about g940 led's for bs. Is anything available for a-10c ? Thanks & Happy New Year All !

Thanks guys.

Been awhile since I've flown. If your flying to a way point & see targets you want to attack. Using CCRP bombing the Azimuth Steering Line (ASL) on works over the way point with the tadpole. How do you change it to attack something else. Hope this makes sense. Thanks,

This isn't a bump. Just miss seeing this thread on page one. :)

Thanks Dark. I am using Notepad++

Hi CEPEGA, I would love to know how to do my own .xml file for HT. A while back I tried cut & patse to make my own .xml, & always got a parser error. I tried your example above, & also got a parser error. Any help is very appreciated. Thanks,