longuich Posted August 23, 2019 Posted August 23, 2019 I wish I was as clever as you. Thanks! Sent from my iPhone using Tapatalk
Fusedspine33 Posted August 23, 2019 Posted August 23, 2019 Please, I have tried to respond to you with actionable responses that pass no judgement. Why you take it as a personal attack is a reflection on you not me. Sent from my iPad using Tapatalk
longuich Posted August 23, 2019 Posted August 23, 2019 It’s all right mate. Sent from my iPhone using Tapatalk
Datajack Posted August 23, 2019 Posted August 23, 2019 Can you link where you had the PCB board printed? Thanks Intel i7 9700K, ASUS ROG STRIX Z390-E, Zotac GTX 2080 TI AMP, Corsair Vengeance 32GB DDR4 3200mhz, Corsair H60 liquid cooler, EVGA 850W PS, Cooler Master: Master Case H500, 1 TB Samsung EVO SSD | Virpil CM2 Throttle, F-16: Thrustmaster F-16/A-10 Stick, F-18: Thrustmaster F-18 Stick | Thrustmaster TPR Pedals | G2 Reverb, J-PEIN Desk mount Throttle, VIRPIL VP-L mount Stick, Cougar MFDs, Generic Custom Built Front Panel, Left Panel and Right Panel, 32 Button Steam Deck.
BulkaCv Posted August 23, 2019 Posted August 23, 2019 I bought them on mouser, but there is big issue with this type of display. top and bottom segments are totaly stupid :( PCB is printed in jlcpcb
Nikolas_A Posted August 23, 2019 Posted August 23, 2019 I bought them on mouser, but there is big issue with this type of display. top and bottom segments are totaly stupid :( Yup, I got the same displays for the AN/ARC-164 and they make for a very strange font. It was the only one that could fit in there, though...
Fusedspine33 Posted August 23, 2019 Posted August 23, 2019 I bought them on mouser, but there is big issue with this type of display. top and bottom segments are totaly stupid :( PCB is printed in jlcpcb I have been following you and your design. Based on your posts it’s hard to tell too much about the design Are you max6954 chips to address the displays or could they help?
longuich Posted August 23, 2019 Posted August 23, 2019 Thanks mate. Seems most displays have issue or another. Sent from my iPhone using Tapatalk
BulkaCv Posted August 23, 2019 Posted August 23, 2019 I drive my displays by pca9685 pwm drivers. It has 16 channels. LED brightnes is controled by pwm duty time. Common anodes are driven by mcp23017 with UDN2981 as source drivers because MCP23017 can source only 25mA per pin. PCA9685 has max I2C clock speed 800kHz - it gives me about 20fps of all LED displays. It is too slow with visible blinking. I will test pwm board with TLC59711 chip with up to 8 MHz
BulkaCv Posted August 23, 2019 Posted August 23, 2019 LTP-4823G can be ideal displays, but they are sold out everywhere
VampireOne Posted August 23, 2019 Posted August 23, 2019 I want to use it for VR anyway so displays are not a priority for me. Sendt fra min SM-G975F med Tapatalk [sIGPIC]If you are still under control you are not going fast enough[/sIGPIC]
longuich Posted August 23, 2019 Posted August 23, 2019 Have you tried 16k33 chips? They work perfectly with 14-segs and 16x8 matrices. Sent from my iPhone using Tapatalk
longuich Posted August 25, 2019 Posted August 25, 2019 Is anyone of you good at CAD? Sent from my iPhone using Tapatalk
avidflyer Posted August 25, 2019 Posted August 25, 2019 Hello, Iam looking for printable annunciator panel for the f 18. Has anyone these things already drawn and share those. Thanks
longuich Posted August 25, 2019 Posted August 25, 2019 Hornet UFC (potentially) Hello, Iam looking for printable annunciator panel for the f 18. Has anyone these things already drawn and share those. Thanks I think i saw one at 40 euros on hispanels. (Which doesnt answer your question, i know) Sent from my iPhone using Tapatalk
avidflyer Posted August 25, 2019 Posted August 25, 2019 Thanks but I mean the once’s positioned over the ddI / mfd
longuich Posted August 25, 2019 Posted August 25, 2019 Oh yeah. The ones with the spd brk and apu fire etc? I’d like to get those as well. Sent from my iPhone using Tapatalk
Fusedspine33 Posted August 29, 2019 Posted August 29, 2019 Pcflights is still developing their center panels. They have the brow panels with lenses. http://pcflights.com/index.php?main_page=index&cPath=47_70_73 Sent from my iPad using Tapatalk
avidflyer Posted August 29, 2019 Posted August 29, 2019 Thanks that the one Iam looking for. I think to print it
Jejestylix Posted August 31, 2019 Posted August 31, 2019 (edited) thank you very much Brun. I realized the UFC and it's amazing. I would have liked to print the lettering externally. But I can not change as I want. Edited September 8, 2019 by Jejestylix
BulkaCv Posted September 1, 2019 Posted September 1, 2019 I have problem with update speed of string values in DCS BIOS. When I mouse click on some button in game. I get string values exported to udp protocol after few seconds.
longuich Posted September 1, 2019 Posted September 1, 2019 Are you certain it’s dcs-bios and not your board or coding? You mentioned flicker problems before. Sent from my iPhone using Tapatalk
longuich Posted September 9, 2019 Posted September 9, 2019 @bulka Do you happen to have solids of your and brun’s ufc models? I can’t get fusion to properly convert those hellish stl’s. Sent from my iPhone using Tapatalk
wereferret Posted September 10, 2019 Posted September 10, 2019 Just want to thank Brun for laying all the great ground work for this project, just finished my own UFC, but I tried to make it just one piece to clamp to the desk when I fly DCS VR... So far works very well... Have a look... Amazing! That's exactly what I'm trying to do with my desktop VR setup. How did you integrate everything? Could you share the 3D files if that's the route you went?
wereferret Posted September 10, 2019 Posted September 10, 2019 It was these cheap and cheerful numbers... https://www.amazon.co.uk/gp/product/B00E1IKGC4/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 Actually seem good for the price, really smooth movement. Definitely better than the encoders. Seeing that image has also reminded me that I still need to make the HDG/CRS panel available to download/print. Apologies to anyone who's been waiting for ages, I'll make an effort to get it sorted this weekend. Were you able to get the HDG/CRS select uploaded? I didn't see it on the Shapeways page. That would be super helpful for the setup I'm about to attempt. Nice work!
Recommended Posts