DCS2TARGET: DCS to Thrustmaster HOTAS LED Controller (Viper Mission Pack, Viper Panel and Warthog)

[kennyuk77]

13 hours ago, slughead said:

Have you tried any of the Thrustmaster supplied scripts?

Yeah for some reason nothing works. I'm  using a TM AVA with the viper grip, Warthog throttle and the Viper TQS button box.

[slughead]

1 minute ago, kennyuk77 said:

Yeah for some reason nothing works. I'm  using a TM AVA with the viper grip, Warthog throttle and the Viper TQS button box.

You’ll need to contact Thrustmaster support to resolve this.

[Crass]

I was able to figure out what my problem was . Slughead you were right there was nothing wrong my setup.

My issue was I have the Winwing MIP and the software for it Simapp Pro wont let TARGET connect to the Viper panel if it running.

The fix was to keep Simapp off, start and run the Scrip from the editor. Once it was up running (Only takes few seconds now) then start Simapp and the Viper panel lights now works in DCS.

Thanks again for the great work you do.  

[slughead]

That’s great.

Whenever there’s a problem always go back to basics. Strip back to just what you need, test, then start adding back one at a time.

It’s the same with DCS. Remove all mods and start from the bare minimum. Add mods back until you find the problem,

[Semtexx]

Hello, i've probably discovered a conflict between DCS2Target and DCS DTC that i can't solve by myself. I don't know if is known but when both the plugin are running (and DCS2TARGET works perfectly) DCS2TARGET blocks TACAN and WPT in F-16, i can use only one of them. The reason is DCS DTC modifies mission LUA files to insert data (WP, TACAN, COM, etc.), DCS2Target sometimes redirects the same files or reads from Export.lua for LEDs and bindings. If both write to Saved Games\DCS\Scripts\Export.lua, one may overwrite the other.

Is there any chance to solve this conflict? Thanks a lot, Andrea.

[slughead]

DCS2Target doesn’t use export.lua.

It used to use export.lua until I found a better way with the intention to prevent the export.lua conflicts.

Also DCS2Target does do any redirection. It’s a read only program.

Perhaps you’re running a very old version of DCS2Target.

[Semtexx]

8 minuti fa, slughead ha scritto:

DCS2Target doesn’t use export.lua.

It used to use export.lua until I found a better way with the intention to prevent the export.lua conflicts.

Also DCS2Target does do any redirection. It’s a read only program.

Perhaps you’re running a very old version of DCS2Target.

Dcs2target 25/04/14, TQS bought the last week, so i've downloaded the last firmware and TARGET software available. Sorry, the reason reported in the last message was ai generated only to help, because i've no idea, but the reality is unchanged: if i want to navigate through DCS DTC i can't use DCS2target and viceversa. Could you give me a chance to use them togheter? Thanks a lot.

[slughead]

1 minute ago, Semtexx said:

Dcs2target 25/04/14, TQS bought the last week, so i've downloaded the last firmware and TARGET software available. Sorry, the reason reported in the last message was ai generated only to help, because i've no idea, but the reality is unchanged: if i want to navigate through DCS DTC i can't use DCS2target and viceversa. Could you give me a chance to use them togheter? Thanks a lot.

Do you have the latest DCS2Target scripts from my GitHub page?

[Semtexx]

3 minuti fa, slughead ha scritto:

Do you have the latest DCS2Target scripts from my GitHub page?

The last files are of 2025, April 14.

5 minuti fa, slughead ha scritto:

Do you have the latest DCS2Target scripts from my GitHub page?

 

[slughead]

Can you provide a link to DCS DTC?

Is it purely software or does it need any hardware, iPad etc?

I not going to promise a solution. I am on holiday this week and have Slugmouse orders to manufacture and ship in my return, then folk from the other F-16 simulator that require some software changes. Then I can take a look at this. However, I very much doubt there is anything I can do, about 0.1% chance and my code only reads data.

Have you raised this with the DCS DTC developer?

Edited 11 hours ago by slughead

[Semtexx]

Viper TQS firmware 1.23...

[Semtexx]

I'll surely contact the DTC developer too, DCS DCT is a very common software and it a valid sobstitute of ingame DCS DTC, here's the link, but i think you know it:

https://github.com/the-paid-actor/dcs-dtc

For the moment i've to tirn off dcs2target until found something useful... thanks in any case. Andrea.

[slughead]

Honestly I’ve never heard of it. I actually exclusively fly in VR, so I don’t see the lights on the Viper. I wrote DCS2Target for fun and interest as there was nothing else available.

[Semtexx]

The doubts still remain: with DCS DTC, as the name, you can import a Flight plan created outside the DCS mission editor using www.combinedops.org (i'm an italian flying group member) but the best is creating a .json file containing all frequencies you need and a lot of other elements. Through the main executable program we can load in less than minute a great amount of data inside the onboard computer. DCS DTC is used with VR too, of course, i use the VR, but i think a solution to make DCS2TARGET working with this, necessary (no Waypoint, no Tacan), program can be find. DCS2TARGET is really fantastic, simple and effective, i'll continue to look for a way.

[slughead]

Oh sorry. The Data Transfer Cartridge that DCS added recently. I’ve not had a chance to use it yet.

Can you provide your DCs.log file from a mission when you have the problem. There may be an error visible in there that identifies the problem.

[Semtexx]

Sorry, this one:

https://youtu.be/-ofsq675eoA?si=qkGQsigsxyNREBp8