RotoDan

I have tried both ways, one session with steam VR and another session with open XRtools. I feel certain this is somthing in my settings, front to back. Why I would like to get a series of screenshots but don't know which keys to use, widows screenshot does not work.

I presume the log file is the most recent session and yes, I first start this with the goggles. I did note there is a new version, I will update this and try later. As for my graphics card, the drivers are the latest supplied by Nvidia. The card is not really intended for gaming, but so far does a good job. It is the Nvidia quadro K6000.

I get into my home fine, I can even bring up my desktop, What I can't find is the launcer you describe. I have DCS pined on my taskbar is the only way I see to launch it. With the reverb on, DCS starts then immediately shuts down. Sorry for being a nooby pest.

OK, been arond the world with this and results are the same. I did find and set enable VR headset, done. I would like some screenshots, what keys do I use in DCS ? also, I have the mouse enabled, but just not there. attached is my DCS log file dcs.log

Well, I have made some progress, finally got the controllers to pair. I know I am doing something wrong or out of sequence. I got to my desktop and launched DCS to the AH-6. What I see is the very same as if no VR. From a cold start, how should I execute all this so the display is in the goggles ? TNX

OK, thanks. I am still trying to figure out open XR, I have that toolkit. I might be trying to run one before the other. Also in the WMR house, my controllers just don't pair so I guess I need to read up on the command lines. I'll try that and probably be back with more questions. TNX

Hi people, Been trying to master the AH-6 little bird and set up an HP reverb VR. problems are the controllers won't pair, but not a game changer. What I don't know is how to use the goggles in the flight sim. If I close WMR and steam VR, I get a default view in the goggles. How can I go about getting the monitor view into the goggles so I can ignore the look around on my hotas ? TNX

Thanks.

This belongs in helicopters, but no provisions for 3rd party. (wish list) 2 add on's for the UH_60L, both tutorials. The hover tutorial, I am finally getting the bugs worked out of, but one main issue is it simply never leaves the ground, 130% RPM, redline in torque. It will roll fore and aft. never breaks ground. If I toggle 'take command' off, the craft just fly's itself into the ground. #2 is the cold start/ Marianas, BUG > the AN/ARC-201 will not key in frequencies, this is where the tutorial hangs. Doing loadout (default), then comms with ground crew, takes near an hour and no/weak audio with ground crew. problem, after 20 minutes, it gets too dark to see on my monitor (sundown). If I just startup, I lose flashlight. Some runway/taxiway lights are just visible. Like flying with your eyes shut. A daytime tutorial would be nice.

Final update: My full screen and aspect problem has been fixed and my 4 added mods are working as they come. I installed the training mission plus the hover tutorial. That was a bit of work combining them to one. They do run fine so now I am down to fine tuning my controls. I am about to toss a wrench in the works going to VR so I will be on other threads. Thanks everyone for your support.

I have got 4 of the free mods installed, one issue with all of them is some flickering mostly the top 1/3 of the screen. most prominent with trees and distant buildings, say like the other side of the runways or fields. Doesn't seem to affect anything but is a slight nuisance. Any suggestions to reduce/eliminate this?

The native windows print screen does nothing so looking at UI layer. I'll be a while before flying, Looks like a failure with the hall sensor in my X-52 stick. center to aft is OK but get a snap to full forward going from center. Got parts on the way, so more hoping.

I downloaded and installed this in DCS, It works with some bugs. I noted the HF radio is mostly inop, that I can tell you about. Mainly used for HFDL when out of range of VHF/UHF comms. 2 modes are AM and USB. HF ACARS, VOLMET. You need frequencies found in MWARA. Back to bugs, The control overlay does not show. I really could use this with my stick setup. I can taxi fine, but IGE is quite unstable. AFCS must be on OGE or crash n burn. Trim release and very hard to maintain attitude.

The screen is squashed running the UH-60L. With the OH_4 it is fine. The AH-4 little bird, I installed but DCS does not recognize it. the only mods that show are the UH-60L and the OH-4 with Vietnam pack. Trying to get screenshots, I have that enabled but don't know the key command.

It is already defaulting to 1920X1080. No issues now with full screen. TNX

I downloaded and installed per directions, but DCS does not recognize it. Pardon my nooby, but what is EFM ?

Hi. My monitor is 1980X1080. I was able to change this after switching the launched window to 2X. So now I do have full screen but a couple of issues with the UH-60 mod. I also have the OH-6 mod and that one works good, so far. I installed the AH-6 little bird, but it is not showing on my installed modules. I am making progress with my issues, who might I contact about problems with the UH-60 module ?

Shots with phone, you can clearly see something is not right.

OK. I can attach 'options.lua , a new issue is this hijacks my screenshot function, I have to restart the system to even get back 'pictures folder' When I do cold start in full screen the graphic are stretched losing like 2 inches on each side. I can't find an aspect ratio setting to correct this Still, the controls settings are scrolled out of view both left and right. effectively, I can't dock my Saitek rudder pedals because the 3rd tab is hidden. options.lua

OK, I solved the full screen problem, much better. A bug I think is still, settings panels/tabs are still partially hidden in the border. My very problem with full screen, was at the bottom right, the OK/save button was nearly gone so even after making changes, nothing was saved. Thanks folks for any help, RotoDan

Hi. Everything does run smoothly, the main issue is not going to full screen in DCS. I did find a couple bugs in the mod like it won't cold start. I will be downloading the latest upgrade and try that. If you look at my screenshots, you see from the beginning the full screen button (between minimize and exit) is greyed out.

That made no apparent change at all. TNX

After I launch DCS, the window is not full screen and the full screen button is greyed out. I also have no keyboard functions other than some basic navigation so there is no way to configure my setup. My module is the UH-60 blackhawk. Other than the install took 11 days, that seemed to go well. Installing the module was easy and appears to be working. Any suggestions for this or a fix ? My system is windows 10 pro on an HP Z840, 164 Gb ram, Nvidia K6000 graphics 12 Gb.