solarwind Posted February 9, 2014 Posted February 9, 2014 Hi I just installed the most recent update for DCS World. I have the UH-1 module and when I go into the training mode the gunner positions (3 & 4) still have not been corrected. When asked to press key #3 or #4 to go to gunner position it just defaults to the front right pilot position. Can anybody assist as I am new to this program. Thank you. :helpsmilie: Brodie
Yurgon Posted February 10, 2014 Posted February 10, 2014 I have the UH-1 module and when I go into the training mode the gunner positions (3 & 4) still have not been corrected. When asked to press key #3 or #4 to go to gunner position it just defaults to the front right pilot position. Huh, it looks like this training is currently botched. When I run it and press the 3 key, the screen flickers and, more often than not, a rocket is fired from the right side launcher even though the "Arm" switch is set to Off. When I press the 4 key, the screen flickers as well, but no rocket is launched. In both cases, I get invariably seated on the pilot seat. If I create a new mission and place a Huey in it, I can get to the right and left gunner seats using the 3 and 4 keys just fine. But I have no clue whether this is a known problem.
solarwind Posted February 10, 2014 Author Posted February 10, 2014 Huh, it looks like this training is currently botched. When I run it and press the 3 key, the screen flickers and, more often than not, a rocket is fired from the right side launcher even though the "Arm" switch is set to Off. When I press the 4 key, the screen flickers as well, but no rocket is launched. In both cases, I get invariably seated on the pilot seat. If I create a new mission and place a Huey in it, I can get to the right and left gunner seats using the 3 and 4 keys just fine. But I have no clue whether this is a known problem. Thanks for the confirmation. Could you send me the mission you created by chance? Thanks.
Yurgon Posted February 11, 2014 Posted February 11, 2014 (edited) Thanks for the confirmation. Could you send me the mission you created by chance? Thanks. I don't think I saved it, so I set up another one. Really just a Huey on the ramp (starting hot, with blades spinning and all systems powered up) with a few evil Gaz-66 trucks to shoot at. :thumbup: My DCS Updater is still downloading the latest patch to 1.2.7, so I created the mission in my 1.2.7 OpenBeta installation. I think the mission is 100% compatible with 1.2.7 (non-Beta), but in case of irregularities, this might be a possible cause. Edit: Update done, tested, mission works without problems in 1.2.7.23803 for me :)yurgon_huey_door_gun_test.miz Edited February 11, 2014 by Yurgon
Svetlano Posted February 15, 2014 Posted February 15, 2014 Hi I just installed the most recent update for DCS World. I have the UH-1 module and when I go into the training mode the gunner positions (3 & 4) still have not been corrected. When asked to press key #3 or #4 to go to gunner position it just defaults to the front right pilot position. Can anybody assist as I am new to this program. Thank you. :helpsmilie: Huh, it looks like this training is currently botched. When I run it and press the 3 key, the screen flickers and, more often than not, a rocket is fired from the right side launcher even though the "Arm" switch is set to Off. When I press the 4 key, the screen flickers as well, but no rocket is launched. In both cases, I get invariably seated on the pilot seat. Brodie I'm having the same problems. Using the Steam version. :joystick:
Recommended Posts