Oliv69 Posted January 6, 2016 Posted January 6, 2016 :helpsmilie::helpsmilie:Since I installed the 2000c I've only been able to use the guns 2 or 3 times, on both 1.5 and 2.0 versions.... The rest of the time I pull the trigger for nothing, with or without radar.... Settings are good ( Master Arm on/ CAS on K1...). Any help I'm getting crazy....
Viking_355th Posted January 6, 2016 Posted January 6, 2016 One of the downsides of 30mm cannons is the low ammo supply. Any chance you just ran out? You should've gotten more than three bursts (I think 8 or so full bursts can be expected) but if you fired more than once at each of 2-3 targets, you may have gone Winchester. When master arm is on, and the gun selected, the lower third of the HUD will show two numbers. If it's 125 and 125, you're at full ammo. If zero, we've solved the mystery.
PiedDroit Posted January 6, 2016 Posted January 6, 2016 (edited) One of the downsides of 30mm cannons is the low ammo supply. Any chance you just ran out? You should've gotten more than three bursts (I think 8 or so full bursts can be expected) but if you fired more than once at each of 2-3 targets, you may have gone Winchester. When master arm is on, and the gun selected, the lower third of the HUD will show two numbers. If it's 125 and 125, you're at full ammo. If zero, we've solved the mystery. You should get minimum 9 bursts, depending on your setting. Check this thread, regarding ammo consumption and burst limiter: Gun burst limiter bug (left/right difference) But I'm not sure if the OP is talking about ammo consumption or the gun not working at all. With master arm ON and gun selected, the gun should fire all right. Did you try with joystick or keyboard? Edited January 6, 2016 by PiedDroit
Oliv69 Posted January 6, 2016 Author Posted January 6, 2016 (edited) My problème is more simple, eitheir it works or not.... With the same settings and manipulations, it doesn't stop after a while... With always 125 ammos remaining on both sides of the HUD. It looks more like a bug, that's why I reinstalled the module on 1.5 and 2.0. It worked sometimes but most of thé times it doesn't... What wonders me is that, having had a look on many forums it only happens with me, both on joystick and keyboard.... A mystery... Edited January 7, 2016 by Oliv69
IvanK Posted January 6, 2016 Posted January 6, 2016 ? Does the Mirage 2000 IRL actually have a Burst limit function ?
PiedDroit Posted January 6, 2016 Posted January 6, 2016 ? Does the Mirage 2000 IRL actually have a Burst limit function ?I don't know, but given the limited amount af ammo I would bet on a solid yes :D
IvanK Posted January 6, 2016 Posted January 6, 2016 Well the Mirage III had 2 x 30mm with just 250 rounds and it didn't have a Burst limiter
Cletust8 Posted January 6, 2016 Posted January 6, 2016 Or is he referring to the CAS pipper which is MIA?
nomdeplume Posted January 7, 2016 Posted January 7, 2016 I would try posting a (short, if possible) track of the problem, that way can people see if you're doing anything wrong, and even take control and see if they can figure out what's happening. Failing that maybe a screenshot or two clearly showing your HUD and the armament panel might help. Not sure if the HUD being in test mode would prevent the guns from working? But it does prevent some symbology from being displayed, so maybe worth double-checking that. The HUD power switch has three positions, off, on, and test. The "On" position is in the middle so it's somewhat easy to accidentally put it into test mode, and it's not especially obvious when it's in test mode. I also haven't tested within having selective jettison enabled will prevent the guns from firing (never tried to jettison my cannons...) but that might be a possibility, too? Probably worth noting that if you've enabled jettison and then close the safety cover, the jettison switch will remain armed.
Recommended Posts