assafm25 Posted December 23, 2016 Posted December 23, 2016 any way to make the trimmer work with the FF joystick? [sIGPIC][/sIGPIC] IAF Bell205 IAF Anafa ----------------------- DCS World Modules: A-10C, FC3, MiG-21BiS, F-86, P-51, KA-50, UH-1H Huey, Mi-8, M2000K, Gazal, Bf109, Mig-15, Hawk and NTTR ----------------------- My System - ASUS Maximus HERO iiiv, CoolMaster 120 Sadion Plus, I7 -6700K @4.0, G.Skill ddr4 16GB ram, Gigabyte GTX 1070 G1 , PSU Seasonic X-650W, OCZ 150 500Gb ssd drive X2, Seagate 7200 1T X2. -------------
Looney Posted December 24, 2016 Posted December 24, 2016 I use the ff2 with the mi8 and have no problems. Sure you need to fiddle with the inversion of axi but that's it, works fine once setup. [sIGPIC][/sIGPIC] Commodore 64 | MOS6510 | VIC-II | SID6581 | DD 1541 | KCS Power Cartridge | 64Kb | 32Kb external | Arcade Turbo
assafm25 Posted December 24, 2016 Author Posted December 24, 2016 Thanks for your replay. Well , No Trimmer for stick when enabling the in game FF Checkbox . Only for the Rudder . [sIGPIC][/sIGPIC] IAF Bell205 IAF Anafa ----------------------- DCS World Modules: A-10C, FC3, MiG-21BiS, F-86, P-51, KA-50, UH-1H Huey, Mi-8, M2000K, Gazal, Bf109, Mig-15, Hawk and NTTR ----------------------- My System - ASUS Maximus HERO iiiv, CoolMaster 120 Sadion Plus, I7 -6700K @4.0, G.Skill ddr4 16GB ram, Gigabyte GTX 1070 G1 , PSU Seasonic X-650W, OCZ 150 500Gb ssd drive X2, Seagate 7200 1T X2. -------------
Rabb Posted December 28, 2016 Posted December 28, 2016 Are you sure? Works wonderfully here, as it always did. MS SW FFB2. Check the following: - In Options, Misc tab, tick the "Force Feedback" option; - In Options, Special tab, Mi-8MTV2 section, in Trimmer drop-down list select Default option; - In Options, Controls tab, "Mi-8MTV2 Sim" section, select "Axis Comands" in the second drop-down list, click at either JOY_X or JOY_Y, and then click at "FF Tune"; "Force Feedback Tune Panel" will appear, set "Trimmer Force [0...100]" (this is centering force) and "Shake [0...100]" to your liking and tick "Swap Axis" option (other options should be unticked); Click at OK; - Now click at "Axis Tune"; "Axis Tune Panel" will open. Set Curvature to 0. All options should be unticked. Perform this step for both axes, JOY_X and JOY_Y. Now, helicopter trim will work like it should. Explanation for the last step - Trim doesn't work properly if there is non-linear response, ie. curvature in response line. For instance, with curvature set to 30, you must deflect stick for approximately 40 % in order to assign a new neutral position at approximately 10 % defleection. Which defies the essence of helicopter trim. With Curvature set at 0, everything works fine. Except controls are very sensitive, but that is something I got used to. I hope there would b a solution for this problem.
assafm25 Posted December 31, 2016 Author Posted December 31, 2016 Thank u Rabb its work !! :) also my landing become easy to made . [sIGPIC][/sIGPIC] IAF Bell205 IAF Anafa ----------------------- DCS World Modules: A-10C, FC3, MiG-21BiS, F-86, P-51, KA-50, UH-1H Huey, Mi-8, M2000K, Gazal, Bf109, Mig-15, Hawk and NTTR ----------------------- My System - ASUS Maximus HERO iiiv, CoolMaster 120 Sadion Plus, I7 -6700K @4.0, G.Skill ddr4 16GB ram, Gigabyte GTX 1070 G1 , PSU Seasonic X-650W, OCZ 150 500Gb ssd drive X2, Seagate 7200 1T X2. -------------
AussieFX Posted January 8, 2017 Posted January 8, 2017 I've had the same problem with my G940. Will try removing the curves, thanks for the tip!
AussieFX Posted January 8, 2017 Posted January 8, 2017 Worked a treat. I was just about to give up on this module and all it was, was curves. Funny thing is I don't usually have curves set with the helicopter modules. Cheers!
Rabb Posted January 10, 2017 Posted January 10, 2017 I may be wrong, but I think trim used to work properly with curves a year ago or less. I would definitely like to have a properly working trim with curves set.
Recommended Posts