71st_Mastiff Posted April 30, 2021 Posted April 30, 2021 is there any way to move the HUD (besides the chair) up and down? I'm sitting at the very top of the cockpit, just to get the whole HUD to fit in the glass. I'm VR 6'3 and would like to fit in this cockpit correctly, with out having my head go through the glass. "any failure you meet, is never a defeat; merely a set up for a greater come back", W Forbes. "Success is not final, failure is not fatal, it is the courage to continue that counts", "He who never changes his mind, never changes anything," Winston Churchill. MSI z690 MPG DDR4 || i9-14900k|| ddr4-64gb PC3200 |zotac RTX 5080|Game max 1300w|Win11| |turtle beach elite pro 5.1|| ViRpiL,T50cm2||MFG Crosswinds|| VT50CM-plus rotor Throttle || Z10 RGB EVGA Keyboard/ G502LogiMouse || PiMax Crystal VR || 32 Asus||
SpaceMonkey037 Posted April 30, 2021 Posted April 30, 2021 4 hours ago, 71st_Mastiff said: is there any way to move the HUD (besides the chair) up and down? I'm sitting at the very top of the cockpit, just to get the whole HUD to fit in the glass. I'm VR 6'3 and would like to fit in this cockpit correctly, with out having my head go through the glass. For all pilot heights the head will be at the same position. The way you adjust your head heigh is by adjusting the seat height, which really ins't necesarry in dcs as when you recenter your VR view it uses head position, which will place your head at about the correct height. Don't remember the keybinds, but if you go digging you will figure it out. The true head position is quite difficult to get, but using cockpit reference points for off-bore degrees in relation to HMCS. This will essentially triangulate your cockpit postion except height. IRL you actually have a swtich on the HUD control panel which helps calibrate seat height. If we get this modelled it will be very simple to set the correct cockpit position, but right now height is a bit more difficult to get correct, I really have no tips for height except to use good old trail and error and figure out what works. Once I figure out my correct position I look for reference points that I can line up to find the correct position in the future. Hope this helps! 1
MartinVoy Posted April 30, 2021 Posted April 30, 2021 I use VR centre position option from UI menu - I did a key-bind to one of my switches on HOTAS. Every time I start flight, I just move around the seat and centre the view. Sometime it requires it to centre while not really in the position you'd like to sit, but once you sit afterwards, it's perfectly cantered. Trial and error - give it a go. I feel you - I'm 6'3. 1 System spec: Windows 10 Pro / i7-12700K / 3080Ti / 64GB / m2 SSD / Orion F16 Throttle / TM Warthog Stick / TPR Rudders / JetSeat / Reverb G2.
71st_Mastiff Posted April 30, 2021 Author Posted April 30, 2021 I'm aware of the UI for VR FOV, I'm just wish there was a way to set the HUD position, while my seat is lower. angle on the Hud; when I set the correct height, HUD to low. "SpaceMonkey" answered what I need to know thanks. Thank you guys... "any failure you meet, is never a defeat; merely a set up for a greater come back", W Forbes. "Success is not final, failure is not fatal, it is the courage to continue that counts", "He who never changes his mind, never changes anything," Winston Churchill. MSI z690 MPG DDR4 || i9-14900k|| ddr4-64gb PC3200 |zotac RTX 5080|Game max 1300w|Win11| |turtle beach elite pro 5.1|| ViRpiL,T50cm2||MFG Crosswinds|| VT50CM-plus rotor Throttle || Z10 RGB EVGA Keyboard/ G502LogiMouse || PiMax Crystal VR || 32 Asus||
Recommended Posts