DmitriKozlowsky Posted October 28, 2022 Posted October 28, 2022 (edited) With external power ON. Turn fuel pumps ON. Press and hold start . Watch until power is at 11%. Advance throttle to IDLE. Watch until power settles on 49-54%. This is broken now. Advance to throttle DOES NOT advance to idle! Edited October 28, 2022 by DmitriKozlowsky
myHelljumper Posted October 28, 2022 Posted October 28, 2022 4 minutes ago, DmitriKozlowsky said: With external power ON. Turn fuel pumps ON. Press and hold start . Watch until power is at 11%. Advance throttle to IDLE. Watch until power settles on 49-54%. This is broken now. Advance to throttle DOES NOT advance to idle! I'm not understanding the issue, could you provide use a track or video highlighting the issue ? Thanks. Helljumper - M2000C Guru Helljumper's Youtube https://www.youtube.com/channel/UCK3rTjezLUxPbWHvJJ3W2fA
DmitriKozlowsky Posted October 28, 2022 Author Posted October 28, 2022 Advancing throttle to IDLE, does not move the cockpit throttle to idle position. I have checked that my thrust is mapped to axis. Works fine when starting mission in air. But in cold start scenario, advancing the X56 throttle up to bring up Mirage throttle to IDLE no longer works. THe thottle that is in cockpit remains locked in OFF position. So something in start sequence has changed. I am gonna try a few things, and if I can't get to work, then post. But in previous attempts , in any module, when I posted a track, it proved useless. Becouse track had different playback for different people. I have latest beta. Others may or may not, which makes track posting a near useless task. Blame on that one on developers. Just not sure which developers. I have had Mirage for two 1/2 years, and use it often. Cold Start always worked. Now something has changed.
DmitriKozlowsky Posted October 28, 2022 Author Posted October 28, 2022 OK. Something has changed, and I beleive that the procedure has changed. Before : Hold down start for 4 seconds or until power is at 11%. Release start and advance throttle to IDLE. NOW: Continue holding down the start , after power reaches 11%, and advance throttle to idle , while holding down start. With X56 this requires some finger gymnastics.
Galinette Posted October 28, 2022 Posted October 28, 2022 (edited) That's incorrect. You do not need to hold start in any way. And the procedure did not change for a couple of months in this regard You likely have an recent issue in your controller setup. Do you have any bind set to 'Throttle Cutoff Unlock' or 'Engines STOP' ? Also check the idle detent value in the special options. Edited October 28, 2022 by Kercheiz
DmitriKozlowsky Posted October 28, 2022 Author Posted October 28, 2022 My binds have not changed. But behavior of Mirage module has. So far only in cold sart respect.
myHelljumper Posted October 28, 2022 Posted October 28, 2022 2 minutes ago, DmitriKozlowsky said: My binds have not changed. But behavior of Mirage module has. So far only in cold sart respect. I did a cold start 2 days ago and it was working as expected, can you share a video of you doing a cold start ? And a screenshot of the Mirage special option too please. Thanks. Helljumper - M2000C Guru Helljumper's Youtube https://www.youtube.com/channel/UCK3rTjezLUxPbWHvJJ3W2fA
DmitriKozlowsky Posted October 28, 2022 Author Posted October 28, 2022 I am investigating. THere are new options in SPecial that I have not seen before. Perhaps the cutoff detente option , set at 15%, is a contributing factor. But right now. To cold start. I have to hold down start while advancing throttle. If I do not hold down STARTwhile advancing to IDLE, the cockpit throttle does not advance. What is Elastic Limit Axis Position? Elastic Limit Bind?
Recommended Posts