Jump to content

Recommended Posts

Posted

Hello collective wisdom…

TG MIP arrived today (bar the UFC) and I thought I’d plug it in and get going.

Assembly and installation a breeze via SAP.  Two issues at this early point…

1.  MPCD bindings are random.  Buttons on MPCD A and B both seem bound to MPCD C.  It’s not particularly apparent in the SAP manual what I am doing wrong.  Are bindings set in SAP or in DCS settings pages?

2.  MPCD screens don’t work in VR mode?

I’d be grateful for a steer please… thanks!

Posted
10 minutes ago, speed-of-heat said:

Re 2, they don't...

Thanks - looks that way in SAP manual 1.2 too.  Looking forward to the mixed reality release whenever it comes…

Still a bit befuddled by the key bindings.  I’m sure I’ve seen a video somewhere where DCS just picked them up from SAP but looks like I shall have to allocate them manually.  

Posted

That's what I did, takes a while, I do all of mine via joypro...

SYSTEM SPECS: Hardware AMD 9800X3D, 64Gb RAM, 4090 FE, Virpil T50CM3 Throttle, WinWIng Orion 2 & F-16EX + MFG Crosswinds V2, Varjo Aero
SOFTWARE: Microsoft Windows 11, VoiceAttack & VAICOM PRO

YOUTUBE CHANNEL: @speed-of-heat

1569924735_WildcardsBadgerFAASig.jpg.dbb8c2a337e37c2bfb12855f86d70fd5.jpg

Posted

Not quite sure understand you!

SYSTEM SPECS: Hardware AMD 9800X3D, 64Gb RAM, 4090 FE, Virpil T50CM3 Throttle, WinWIng Orion 2 & F-16EX + MFG Crosswinds V2, Varjo Aero
SOFTWARE: Microsoft Windows 11, VoiceAttack & VAICOM PRO

YOUTUBE CHANNEL: @speed-of-heat

1569924735_WildcardsBadgerFAASig.jpg.dbb8c2a337e37c2bfb12855f86d70fd5.jpg

Posted
5 hours ago, Soupdragon said:

Assembly and installation a breeze via SAP.  Two issues at this early point…

1.  MPCD bindings are random.  Buttons on MPCD A and B both seem bound to MPCD C.  It’s not particularly apparent in the SAP manual what I am doing wrong.  Are bindings set in SAP or in DCS settings pages?

Sounds like you have then all set to MFD1-C.  In SIMAPPRO when you pick each of the MFD's on the right side middle assign each of them to: MFD1-L, MFD1-C or MFD1-R.  Change them out and you should have 3 separate controller columns in the DCS bindings that you can bind individually.

  • Thanks 1
Posted
On 7/29/2023 at 2:00 AM, rob10 said:

Sounds like you have then all set to MFD1-C.  In SIMAPPRO when you pick each of the MFD's on the right side middle assign each of them to: MFD1-L, MFD1-C or MFD1-R.  Change them out and you should have 3 separate controller columns in the DCS bindings that you can bind individually.

Nope, that wasn’t it.  Bizarrely the issue is fixed and the only thing I have done differently is connected the devices direct to the motherboard and that shouldn’t make a difference whatsoever…

  • Like 1
Posted
2 hours ago, Soupdragon said:

Nope, that wasn’t it.  Bizarrely the issue is fixed and the only thing I have done differently is connected the devices direct to the motherboard and that shouldn’t make a difference whatsoever…

That's weird, but glad it sorted itself.  Was it a powered hub you had it in originally?  Not sure why not having enough power would cause the symptoms you were seeing though.

  • 2 weeks later...
Posted

when any of you start the SIMAPP Pro then start DCS do any of you get a half green screen across any of your MFD's. I get a green square that blocks half my bottom MFD and 2 small corners in my left bottom right, and right bottom left MFD's.

Posted

Shouldn't quite cause the pattern you're seeing, but double check that you don't have the option to turn screen green for ID purposes left on in SIMAPPRO.

Posted (edited)
3 hours ago, -HINDSIGHT- said:

when any of you start the SIMAPP Pro then start DCS do any of you get a half green screen across any of your MFD's. I get a green square that blocks half my bottom MFD and 2 small corners in my left bottom right, and right bottom left MFD's.

Some pictures might be helpful?

....and show us your Simappro MIP settings

Edited by MustangSally

Ryzen 9 7950X3D - MSI MAG X670E TomaHawk MB, ASUS ROG Ryujin III 360 AIO

64gig Corsair DDR5@6000, Gigabyte GeForce RTX 4090 AORUS

Winwing Super Taurus, Orion2, TO / Combat panels, Collective with Topgun MIP

Winwing Skywalker pedals, NLR Boeing Mil Edition Simpit, 55" Samsung Odyssey Ark, Trackir

Posted

working on Pictures but I think I found issue.

 

Ok I think I found the problem. Video works great its my simapp pro software adds something to my lua file. When I load back in my DCS resolution changes from 1152x2160 to 1152x2680 or something weird like that. I think it is adding the MFD's resolution to my 2160. I So I will post in the Winwing MIP page to see if anyone is running tripple screens with the WInwing MIP to see how they got around this.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...