A.F.

I have attached my trackball with velcro to my left knee

Hi, can someone tell me if it is possible to run a fan only when I open the cockpit canopy? Simshaker for Aviators controls the buttkicker via the audio output of the PC Can I do something similar to the action "open canopy" and control a relay that then starts the fan?

Hi, I use Leap Motion because I don't have hand tracking available with the G2. Leap Motion is unfortunately only supported by modules from ED. It works very well (two-way switch and pressure switch and is really fun, plus it's very good for immersion. In other modules I use PointCtrl. Luckily I was able to get another one. But either you can't buy one at the moment or you have to wait a year for it. I also use a trackball with my left hand. With a little practice it works very well. My next HMD has handtracking and I will continue to ask ED for better Leap Motion support!

Really?? I have to try that out right away

Tracking the hands is possible with Leap Motion. The virtual fingers move like the original. And you can operate switches in the cockpit. (Only with ED modules) However, the hands do not create shadows

Because the last time I did an update, SSA stopped working. It took me a few days to get it working again. I would like to avoid that.

Hi, I have noticed that the catapult start of the F14 is no longer transmitted to my buttkicker. All other sounds work. Were there any problems with this in the recent past that were fixed with an update from SSA? I have a pretty old version. However, I would not like to update.

It may be a stupid question: Is it possible that your eyesight is not so good anymore?

Hi dureiken, Exactly as edmuss described it. Instead of a finger app I use PointCTRL

hi, I'm just trying to make friends with DML. So I am still very new here! I would like to start a smoke only when I enter a trigger zone with the plane. I already know how to place the smoke and I can do it. But I can't get the smoke to start until I fly into the trigger zone. Can someone help me?

Please, ED - disable the function that the virtual hands can control the hotas! This function is not needed. Nobody flies a plane in DCS without hotas. Also, the hands automatically grab the hotas when they are near the physical hotas. When this happens, two things happen: 1. due to the input delay between head movement and Leap Motion, the virtual hand moves without me moving my real hand - just by my head movement. 2. the interaction between Leap Motion and cockpit is permanently interrupted by the grasping hand. I have to go back to the menu to reactivate it. So, away with it! - get your third party developers to support Leap Motion! There is nothing better for immersion than being able to operate the many buttons and switches in the cockpit with my own hands! Thank you

I use Leap Motion without PointCtl only in ED aircraft. Unfortunately, third-party vendors do not support Leap Motion. In these airplanes, I use Leap Motion and PointCtl at the same time in such a way that I only display the virtual hands through Leap Motion. This gives me a better feeling when clicking switches in the cockpit with PointCtl. Did this help you?

Yes, here

Is boresighting with tgp and maverick on the ground still not possible after the cold start? When I aim the tgp at the target, then press handoff, the seeker of the maverick does not go to the target.

Please Razbam, give your aircraft leap motion support, please

I noticed that my virtual hands have a distance of about 3 cm when I put my index fingers together. Even when my physical index fingers are touching. Does anyone also have this problem?

For even more immersion I have an idea: please add Leap Motion support for your modules!

Hi, since a few days i have the problem that the throttle in the plane changes to the cut off position, although i have the throttle only in the idle position. I have not changed anything in the Virpil software. When I move the throttle to the idle position, the two buttons that I programmed for the cut off are activated. This is new and should not be. Does anyone know a solution? MT-50CM3 Edit: I have found the error. Apparently my physical detent has been misaligned.

What resolution do you have in OpenXR? With my G2 it says something like 2560x2560... No matter what I set. 100% or 200% it is always the same resolution displayed

I adjust my seat position with forward - back - up - down in the control settings "cockpit views". There you can assign buttons for the movements. So I can tune my seating position well after I have centered my HMD. Does the description help you?

Unfortunately, I have no idea in which thread I should write this. Leap Motion is not treated well... I have used Leap Motion and PointCTRL at the same time in the past, so I can see my virtual hand in third party modules and still operate pointctrl. At least that has worked so far. After the last update either one or the other works. Why does ED change something like this but doesn't it create this useless function that leap motion can move the HOTAS? I don't understand it. I know my problem is very specific but I need to vent my frustration

Hi, it's a little strange, when I click on "open-XR Runtime" in OpenXR tools, it says "Show configuration" with a resolution of 2535x2474 pixel (HP G2). But in the OpenXR toolkits in DCS it says 3168x 3029. I have in OpenXR tools custom rendering scale on 100%. What resolution should be in the OpenXR tools for the HP G2?

I have a time delay between my hand recognition and the display of the virtual hand. When I hold my real hands in front of me and then move my head up/down/right/left/, my virtual hands also move briefly in that direction and then go back to the starting position. This should not be the case. The virtual hands should be independent of the head movement. Please remove the possibility that LeapMotion can move the HOTAS. Nobody flies the plane with LeapMotion only. That doesn't work because the hands move with every head movement, and therefore also the HOTAS. If the time delay (see above) disappears, this function makes more sense

Where did the thread for leap motion and point ctrl and SSA go? Have I not noticed something