warmachine79

Hey guys, in order to play with my Pimax Crystal Light on 72hz stutter-free, I want to lock/limit the DCS FPS to 72. However, the game menu only allows 5 fps increments. Any ideas?

Sorry, I do not now where I had that 700 GB figure from.

How did you do that? The Iraq map alone is 700 GB. Are you running DOS with doublespace compression?

I refer to the thread title ;). My 1TB PCIE 5.0 DCS M2 is FULL and I need to go for a bigger drive. I have quite a lot of stuff and I wonder if a 2TB will be sufficient. So, what is the biggest possible DCS installation at the moment?

I narrowed it down to that I will use aluminium profiles. This one looks good and it is compatible to aluminium profiles. GT position could be for flying, F1 position for racing. With the pedals in F1 position and the seat in GT position, plenty of space on the floor for rudder.

Hey guys, I currently have a single rig for sim racing and I fly on the desk. I want to build/buy a dual rig. Requirement: some solution that allows to have both rudder pedals (Winwing Orion) and racing pedals (Fanatec Clubsport Pedals V3) without having to switch around something. Of course, the wheel will be in the center, thus the Flightstick (Winwing F16EX) will be on the right and the throttle (Virpil CM3) will be on the left. I also want something where I can place mouse and keyboard and both platforms need to be movable. And in case you think I am not complicated enough, the seat should be in a lying position for racing (so Formula seating, not GT3 like a truck driver). I am also fine with the seat being in that position for flying, though. Currently, I have this seat and it would be great if I could use it for the rig or get a comparable one when it comes to the lying position (in particular with regard to the comfortable hip flexion angle): null

It is extremely comfortable; I have both for Q3 and PCL third party comfort straps and the PCL is more comfortable; I can wear it for hours. Also with the factory strap - which is a catastrophe on Q3 - the PCL is more comfortable by far. I never tried the OG Crystal, but the PCL is also lighter as far as I know, because it has no battery pack. I do not have any chromatic abberation in DCS, but in AMS2, there are some infoboxes where the edges show slight chromatic abberation. The first pair of lenses I had for the PCL had an unachievable sweetspot, because if I had the sweetspot for left eye, the right eye was distorted and vice versa. I contacted PCL support and recevied a new pair of lenses. The sweetspot now is great on both the horizontal and the vertical plane, whereas you have to move the headset to a certain positiion in order get to the sweetspot on the vertical plane (for me, it is that I have to move it rather down). With the Q3, the sweetspot is bigger due to the pancake lenses. However, there is a sweetspot for the PCL and I think it is not a problem that it is smaller than the sweetspot of the Q3 once you have found the sweetspot.

I used G2, Q3 and now PCL and the Q3 is ahead of the G2; but if I had only a G2, I would not spend money to upgrade to Q3 as the difference is not sufficient to justify the additional money to spend on the Q3. I would save it and go for the PCL. The PCL is in another league when it comes to the overall picture quality. Plus, it is the most user friendly headset when it comes to setting it up as the Pimax Play software is easier to adjust than going through all the hassle with OTT and Virtual Desktop. However, if I had to buy a new headset without already having one, the Q3 is an option.

No, that's raw power regarding the advantage of 4090 over 3090TI.

So you got a 5090 working with a Pimax Crystal Light? There are reports in Discord that Pimax HMDs do not show a picture when connected to a Blackwellcard. Also confirmed by Quorra which is some Pimax official.

When will that be, by the way?

I works for me now, but I think Devs should make a small update to DCS that implements the new DLSS so that you do not have to manually copy DLLs and so on.

Ok, that is confusing now. What do I have to do use Modell K? The .dll I downloaded some days before only has Modell J.

How do I do that? I am too stupid to find that. I just find the like button. And can "report" or "share" via the three dots in the top right.

Thank you, that worked.