Moxica

Fwiw: I just run it @120Hz on the 4090. -Never looked back.

"From the very beginning, this mission was designed to annoy you." -A very bad decision and a huge turnoff.

Good news! How are they coming along?

Oh!

Nope. Talking about mission two. I was in formation with two Kiowas. Looking at them as they disappeared. ..on the way to a training/firing range.

This is looking very promising. I had the best of times in the kiowa. (Struggling for a while before I understood, I was not to land on the tug. -Came very close. Had to abort mission two, however; My comanions just disappeared. Not so much as a "poof" -Did not appear on the map or F2 either. -Just went into the twilight zone after a few miles. I've never seen this before.

Yes! That is it! And I found it! Page 64 in Chucks guides: HUD Depressible Reticle Switch. " •FWD: STBY (Standby) displays the standby reticle and removes all other HUD symbology •MIDDLE: PRI (Primary) displays the primary reticle but does not remove any HUD symbology •AFT: OFF" Thanks for your effort,guys! :)

What's the recommended PC setup or graphics card for the Crystal Light? GPU: RTX 3080, RTX 4070, RTX 3080 Ti, RTX 4070 S, RTX 3090 Ti, RX 6800XT, RX 6900XT, RX 6950XT, or higher. CPU: i5-12400, i5-12490F, i5-12500, i5-13400, i5-12600, i5-14400, i5-13490F, i5-12600K/KF, i5-14490F, or above.

Thank you. Hope this makes more sense..

Just learning cold start. I get this crosshair -ish symbol in HUD when I cold start the F16 What am I missing?

It's official!

That is what I (think) I've experienced. -Was CPU bound. Pushed eycandy up.. Also running Pimax @120Hz. Visible range to extreme. Got better graphics AND a fluid flight experience.

Well. I got the cold war Germany map yesterday. Wow! Ugra Media puts the cabinet in its place! On that note: ORBX: Microsoft just called. -Heard you're leaving "early access" They want their FS2000 graphics back!

New map! That is quite a gesture! Not bad, not bad. (That is norwegian for "great", esp. when you say it twice like that ) Thx a bunch!

Try this in Chrome: Press Ctrl - shift - delete (It is "SHIFT", mind you. Not alt.) Click "Delete data"

"it should work out of the box" ..It doesn't Put your PC specs in signature or smth.. Answer is namely "it depends"

It is getting there: I've been stubborn, and used latest (1.39.4.99) PimaxClient in combo with Quadviews companion and Quad-Views-Foveated-1.1.3 over the last couple o' days. I'm running @120Hz. It is the best version I've seen of DCS. Sometimes it wobbles/swims, and when it does, it is a complete mess. Solution is to restart PC. Lately I havent had to do that much, and it seems pretty stable. Hope it last, because this is beautiful. -Touchwood!

With latest firmware I have found: Pimax client 1.39.2 works without wobble/swim if you do not use Mbucchia Quad-Views-Foveated Latest client software wobbles regardless. Best solution at the moment (for me) is latest firmware, Pimax client .1.39.2 and no QuadViews companion. -Sadly, I'm back to more mediocre framerate, bu at least the cockpit is stable.

In Pimax play client, you must restore all prefs and settings. Not in DCS.

Thank you. ..Yes, I'm aware of that. Except the bit about the floor. I mean.. really? Tested again just now. Rolling back again.

Try re-installing Pimax play software, ticking both boxes. -Including the "Remove cached data..." null

Agreed. How come it never remember my room setting? It is out of whack everytime I start the set. I am stationary sitting down. The new calibration procedure seem to scan the room, but for what? Next time I use it, the centre is to my right, because I leave it to my left after use. And sometimes I find myself jumping betweeen cockpit, and three meters above. Back and forth. The worst experience is the "swim" phenomenon, where the cockpit gets to be stationary in front of nose, but with a little lag. -But I've got a tip for you regarding sound; Turn off the "Pimax as default" and set sound prefs in DCS menu. -Although DCS does not remember sound preferences, you can set radios to Pimax, and world sounds to PC-speakers. They should be default.

Sad to say, that did not last very long.. Swimming is back, and Pimax not remembering room setting. ..rolling back to 1.39.2

There is a radio/tickbox at the beginning of the installation. Tick that! Not sure if the word "flush" is used. but there are only two boxes to tick, and one is allready ahem.. ticked.

..and it is so good to be back. For several months, due to tracking problems, swimming image (and a few other "inconveniences") DCS has been totally un-flyable to me. Today, I found a(nother) software and firmware update for the Pimax set. Installed it, and everything got even worse. Tech support answered within five minutes: "Re-install, but this time, flush all settings." Now, I'm not even using Mbucchia's software. (Had one instance of severe "swimming" but restarted PC, and from what I can tell. It's all kosher.) Goddammit, guys. You have no idea. The struggles. The frustrations. I once chewed my left arm off at the elbow. -Didn't help. I also have been known to utter "grrr" just before sleep. Didn't help either. Update, and a kind advice from tech support did. -I'm having a beer now. A large one. Cheers!