RokaOvO

I remotely controlled my friend's server and solved the problem by messing around with the GUI of the router XD

I contacted the server host and he said that UPNP on the router was always off.

Here dcs-server.log dcs-client.log

Tried uninstalling Olympus as well as very simple tasks, but the truth is still like that. Retesting, the above is what I tested on my friend's server earlier

My friend opened a server, but when I tried to connect to it, the loading progress would get stuck in "Mission Load Done" for a few minutes and then pop up "Server Latency Timeout" and get kicked. This error is not an unresponsive at the time of "Mission Load Done", but is displayed as a response state, and the normal progress should be "Net Sim Post Start" I called a friend to connect to the server and the same error occurred The server can be seen directly in the server list and can also be connected via IP. I tried connecting to a different server and it worked. dcs-server-20240411-083357.log dcs-client.log

目前这个问题我只见过两次，一次在VR上，一次在PC上，两次相同的点都是在多人游戏内，我坐在后座且前座有玩家操控的情况。(两次情况不在一个服务器内) VR上的GPU是几乎占满的情况从起飞后一直出现，PC上只有一小会帧数比较低的情况出现。 有一个类似于"未完成或者外部视角的模型"在座舱内反G运动(貌似只会在低过载的情况下出现)，消失之后持续出现。并且严重情况下座舱外的F15模型会扭曲。 大概跟前座当时的无限伸长手臂是一个性质。 参考视频链接：https://www.bilibili.com/video/BV15W4y1F7Dj以及https://www.bilibili.com/video/BV1fy421i7VW

把你做好的任务放在例如D:\SteamLibrary\steamapps\common\DCSWorld\Mods\aircraft\FA-18C\Missions\QuickStart的文件夹内，然后在主菜单里找快速行动或者任务一类，摸索摸索，不是很难。 此例子为STEAM版DCS的F/A18模组快速行动任务列表文件位置。 文件夹来自DCS的安装目录，不是保存的游戏内，是官方模组安装的位置。 不知道这种情况会不会红盾。

The front seat of the F15E does not have this problem, and the rear seat only TPOD aiming pod target designation control is reversed. I don't know if joystick users will have this problem. By the way, the air conditioning of the F15E is noisy

In the current version, the F/A18C's keyboard pitch output freezes when the keys stop and returns to the very center after a short time. My suggestion is that when the pitch button is released, the output value goes straight back to the center, and when your pitch output returns to that position, the F/A18C flight controller will fix your aircraft pitch in that position. This issue is related to the F/A18C's Automated Driving (BALT) not working properly when the output value is not directly centered 以下是中文描述： 目前版本中，F18C你停止按下俯仰对应的按键时，杆量指示器中你的杆量不会在正中心，过一段时间则会自动重置。 我的建议是：直接设置为你停止按下俯仰对应的按键时，杆量会自动居中，因为F18C的飞控会在你杆量居中时让你的俯仰也不会上下移动，并且,这个问题如果杆量不在中心，自动驾驶的BALT模式无法运行。