Skymad

I don't know if it's realistic, but I change HOF to 700 - bomb disintegrates low above ground, therefore no compensation is required.

Ok, I will attach track when this happens again (probably tomorrow). My specs: Phenom 955 Gigabyte 870A-UD3 HD6950 1GB with newest official drivers 6GB RAM Samsung HD502HJ 500GB XFX Core 550W Everything runs perfectly, but DCS World. It very often freezes/crashes (dcs.exe stopped working)/"connection interrupted" (this most of the time). I only play (or at least try...) on servers with low ping, never above 100, usually around 50. Good, stable, 25mbit connection.

Today I tried again, and again multiplayer is UNPLAYABLE. Crashes/disconnects every few minutes.

I have these weird multiplayer issues as well. Instability of DCS World's multiplayer is just pathetic! I hope it has the highest priority to be fixed... otherwise it's shame on you, ED.

Yea, Dragon's training is good for learning. But Dragon's missions I find demanding :joystick:

I think multiplayer is rather bad for newbie. Most of the servers are running hard missions, which require few aircrafts for cooperate, and are much much more difficult than singpleplayer ones. Just read manual, watch youtube tutorials and try singleplayer.

Thanks for your reply. I've been experimenting with Vikhr range; at 300m AGL I could hit targets 10km away, with missile speed of 450-500km/h... but I know, it's not the way they are meant to be fired :) Next time I'll try to lock target at 8km, and wait for launch permission while slowly getting closer. PS Upload more BS2 videos on your YT channel :D //@up yes, It was possible in 1.1.1.1... probably it now works correctly.

And one more question :) Is it natural, that Shkval doesn't lock onto a tank from 9-10km? Just happenned on multiplayer session. Sensor status ТГ. Like it didn't "see" the tank, but it was in open field at range of 9km. I couldn't lock onto any of the few tanks. (?!). Of course laser armed.

I know that, thus I try to engage A/H always above 4m AGL. Typically at 250-290m 9km away from the target.

I have another question: why sometimes engaging autohover disables ATT, BANK and HDG channels? Helicopter goes crazy when this happens. I engage A/H mode mode at ~10 km/h, so it should work. I noticed it always happens when there is no speed indicator on the HUD (+xxx in the upper-left corner of the HUD). Speed indicator on the HUD sometimes appears few minutes after takeoff... but everything seems to be turned on.

Hi, I have a question about campaign: is it me, or the AI doesn't turn on datalink? When I try to send wingmen coordinates, send/mem button is flashing - he didn't receive message. Also when I tell him to attack datalink target he responses negative/unable... I noticed that when mission starts on runway datalink switch on radios panel isn't turned on... but when I start the helo manually AI datalink works. Any ideas? DCS World 1.2

Yes, I disabled multithreading and power saving in BIOS.

The funniest thing is, that I have only 17" monitor and play in 1280x1024... still trying to figure out why cockpit of BS2 causes ridiculous lag. While flying above sea I have only 20FPS in cockpit, but 60 outside. I did not experience that sick lags in A-10C.

Yep, already disabled TSAA and unticked "disable aero interface"

I have terrible FPS too :/ In cockpit of BS2 i have 13FPS... Phenom 955 @ 3.4GHz HD6950 1GB 6GB RAM Win7 x64 Already disabled Catalyst AI, reduced settings... I can play Battlefield 3 on high/ultra, but DCS World lags as hell...

Did you notice changes in weapons' behavious? GBU-12 seems to be less accurate (still almost always hits its target though). I also noticed horrible accuracy of wind corrected Mk-84s. They never hit target. I tried Mk-82s, still are accurate when using wind correction. Could someone try dropping Mk-84 from 10000-15000ft using wind correction?

I also noticed that datalink doesn't work... at least in multiplayer.

I tried singleplayer "shooting range" fast mission, comms menu not opening at all.

Awesome news! Is ground crew's "repair" option finally working?

Change HOF to 700, works perfectly for CBU-97/105.

Update video drivers to the newest, helped me. //edit: helped for first run, now it crashes again! Are you kidding me?

Finally got it working. I updated video drivers to the latest CCC 12.6. //edit: helped for first run, now it crashes again! Are you kidding me?

Now it's starting to piss me :mad: I tried to rename DCS folder within saved games, as well as changing internet speed in game and reinstalling Visual 2010 x86. Still the same CTD. Any ideas?

If you want to play on "high" settings, you need an i5 and definitely W7 x64. Card is ok even for DCS :)

0.2GHz is not worth increasing voltage to "danger zone".