FOXFIRE TWOONE

The left/right wheel brake commands, sets/locks the brake. I tried them on the CH PRO pedels and would set and release with toe. I stop using that because when taxing and landing, I would sometimes lock them and when I tried releasing the a/c would not move. Pressing on the toe one or both would not release. That became very frustrating even with a good size Dead Zone on each axis. WWWWWWWWWWWWWWWWWWWWWWW :D

Something I have never tried to use in a mission before. Where do I located them in mission editor. :book:

So is the CSM sys completely impletmented. I ask this because my RWR switch only toggles between on/off and not to the third position ( menu ). So how are you programming. Or am I not getting all out of the Manual. :helpsmilie:

Thanks to all for you input on the A/P. In one day I have gone from being very frustrated to ( very confident ) that I can learn this SIM. I am now able to ( Lock Launch and hit targets with MAV's with ease now, and drop bombs on TGT in same run. ;) :pilotfly: :)

I had A/P on before I tried to lock but disengaged it because the times I got a lock with it engaged the same thing was happening, and I would get the audiable, ( warning autopilot ), disengage it, and still the rollercoaster ride after the disengage. :noexpression: ? So as long as my distance is not to (close) and (alt), not to high the A/C should fly strait and level during lock with A/P engaged. Or dose either to the two matter pertainging to a lock and flight sys when using MAV's.

Well I finally got some MAV's off and on TGT today :) but after first lock and launch the A-10 rollercoaster'ed and I could not figure how to stop it. Could someone point me in the direction in the :book: manual that covers this senerio. Or a hint too the solution. :helpsmilie:

Just had to be SAID :book: :P :thumbup:

:doh: Yea Thanks :pilotfly:

Has the ability to use mavs in missions we create not been implimented yet when starting on ramp or runway. When I click on MAV button on the MFCD the screen goes black and mavs OFF. If I start the mission in the air the MAVS are available for use. Thanks

Thanks ( jerda ) that lets me know that I was close, before my TRI suddenly stop working. Must have been under more pressure than I. ( einar-st ) :lol: And yes I am reading the :book: but even after the first ever A-10 trainning flight I am sure the military used ( vids in their trainning ) for new pilots. :pilotfly: :joystick:

Anyone know of any vids out there on weapons usage, and steps. My Trainning is not working so this could ease the pain.

Trim works only with keyboard by pressing ( ctrl ) first then key. But when I assign that way in solfware they don't work. If if reverse the the ctrl and key, that don't work. Then don't work on any hotas key assignment in SST OR SIM. I will uninstall.

FF has been disabled.

Correction the trim dosen't work anywhere. I have tried programing in both SST and in SIM no go. Now since last post I took a brake, jumped back in the Sim and now my TIR has stoped working. Thought it my be a problem with the TR-5 solfware since I periodic issues with it and TR-4. Installed the 4 solfware. It starts up and then the green light go out and no op. With the 5 solfware the green light will not even come on, but the red lights will show for both. I am cursed. :mad: :cry:

I made mission to just fly and get feel of A/C. The neither the AP or the Trim, all axis will work, even using keyboard inputs. And, I did a default reset to all. No problem in instant action or missions, they work. Is this know issue or mine. :mad: :helpsmilie:

:doh: Did reallize there were four files. Yes only setup exe. :megalol:

I just downloaded and it only took 40seconds. I hope I got everything for my 59. bucks.

:thumbup: Went to my local Target store today, for a few items. Thought I would check the PC games and Sims for any surprizes, and :D there they were. Two box Lockon platinum, now minus one. :book:. Late but too he who waits.

Two things you might try. Assign the wheel up/down to do nothing, save, close out n52, open then assign again 7/8 save, try it out. Or try assignning in micro editor. Also under micro editor open any key assignment to view the files, delete any previous scroll wheel files and start over with it's assignment.

I am still on 1.0.1 and it works fine for me. Are you remembering to save changes after assignning. ?

So what folder inside the sound folder are you placing your wav files.

Will my wav files work in 1.1. I have tried making a few files and putting them in the sound folder but when i nav to the folder in miss editor they do not show. :music_whistling:

Ok, I jumped in, put on my thinking :smartass: cap and reading :book: cap and figured out some simple triggers, and messages. Wasn't as tough as I thought, just trial and error. :D

Is there a video out their on how to built a mission, setting triggers, rules, and actions. :helpsmilie: If not, it would be welcome'd if someone :smartass: could do a short basic vid for us not so bright. :book: Simple missions I know the rest, well. :doh: Thanks

I have been unsuccessfully trying to assign the key commands but when I push the assign button the MFD is what changes. The # 1234 for the begginning of each rotary assignment dose something else so how do U assign a combination of key strokes like R-1+LCTRL+LALT. Or is there key assignment glitch.