Loadie

Looking for some help with programming the stream deck for use in Multiplayer mode if possible? When I try to start it asks me for a Server IP and port number. Also how do you program the buttons? Like -artillery, .00000000001 so I don't have to contsantly type it in, just press the button and away it goes... Thanks

Hey all, I just became a Game Master on a MP server and we have been having an issue with neutral units not showing on the F10 map anymore. Apparently this is a known issue with ED? Is there a planned fix? Is this the way it’s going to be? I know loads of folks are frustrated now as they showed in the past on the F1- map, but in a different colour. Can this issue be resolved, or has it been determined that this is the way it’ll be from now on? thanks Loadie

Yes, we use the CTLD menu to load crates from FARPs or logistics tents.

Sounds good, I have posted in the server I spend 99% of my time on. Everyone that has the same issue will also post their track file here as well.

Where would I get that from?

It seems to be a common problem for me, and others . I use multiplayer mode on a few different servers. But, all seem to have the same issue. I pick up a load of crates, try to fly to destination, mid flight the load just disappears out of the cargo compartment. Also on the offload page, they’re also gone. I’ve tried numerous different ways to stop this, including closing the ramp and door completely; however, they still disappear. anyone else running into this issue? I’ve been told by server managers that ED knows about the issue, they have for some time, but no solution yet?

Hey there, ‘’I’m trying to figure out if it’s possible to program a button box for the CTLD menu? I’d like to press 1 button and have say 1 Abrams tank crate appear in front of the Chinook. Is this possible to do with a button box? To get to the tank crate I have to select the comms menus, then, CTLD, other, ground, heavy machine, then whichever tank I want. I hate losing the mouse on the screen. is this a simple or doable task? I’ve been told that it is doable, but you need to buy vioce command or other programs. thanks

I’m in the process of making a CH47 CDU, the issue I’m having is the proper dimensions.

Thanks for responding! I’ve got it sorted out. Just need to get it working through oculus virtual desktop now…….

Hey all, Just wondering if anyone happens to have or know where I could get the dimensions of the CDU? I’m on the process of making one with my 3D printer, just need the proper dimensions if possible. thanks much

LorenLuke, thanks for explaining that, suffice to say, I have it working for me now…… Well, I did, until I hooked up the Moza AB9 FFB base. Now, I’m completely lost. That’s gonna be another steep learning curve, lol

Hi all, back again with yet another issue I’m having. Here is my setup today, I’m waiting for my 9800X3D to arrive so I can install the new PC. But until that arrives I’m having a massive issue. Oh yeah, my setup, I7 11700K 64GB Ram, RTX308-Ti FTW3, with 3 x M.2 SSDs. Issue; when in DCs and flying the Apache the monocle is way too high in my view, the heading take can barely be read, even with the headset set to all different angles, same results. Then I try to use George AI and the AI pop ups are set to victimless, not horizontal. The second pop up is so high 1/2 isn’t even in my view. I’m assuming it’s some setting I have in either DCS or Oculus software. someone with the Quest 3 that’s not having theses issues, can you post your settings, so I can compare and hopefully resolve the issue? I have a ticket in with ED, but they’re asking for photos or video of the issue. When I try to do that. I press the oculus button and pull the trigger, just like the manual says, in my case I get the DCS folder in VR pop up and it asks me if I want to recenter the view or quit DCS. When I try to take a photo or video, I pull my headset off and the eye pieces immediately turn off, so I can’t take a screen shot, photo or video. i asked ED if they could add something so we can adjust the monocle, they said they were currently discussing the issue; however, not enough people are complaining about it, so they’re not inclined to make a change. They’d look at my issue for sure but I need to supply evidence, which I can’t!

There has to be some setting in the Q3 that can fix this issue! Now when I use George AI, the AI pop ups are vertical vice horizontal. I’ve got a ticket submitted with ED; however, I can’t even take a screen shot in the Q3. When I hit the oculus button and pull the trigger, all I get is the DCS folder pop up and it asks me to readjust the view or do you want to quit DCS. I can’t even take a video of this as the second I remove the headset the eye pieces shut off. I’m so confused now!

Got it sorted out, lol.. my fault, as usual…… So I thought that it was simple trigger issue. I didn’t realize that you need both left and right triggers to work to shoot. I now have it working. thanks everyone for your help, greatly appreciated!

Yes, that’s what I’m doing. I’ll try to setup like another poster below yours. See if that works first. There is a 3 position trigger on the Alpha. The guard is 1, then the trigger itself has 2. But, it was suggested that I use the trigger guard as the laser then use the trigger itself as just that. I think that’s what he said. I will give this a shot 100% tomorrow, thanks much!