fitness88 Posted June 12, 2018 Posted June 12, 2018 Once I crank right engine I try and move the right throttle to 60% in order to bleed air...I don't have a right and left just 1 throttle. So what do I do? Thank you.
fitness88 Posted June 12, 2018 Author Posted June 12, 2018 use the keyboard I tried but no joy. 3. APU switch to ON and wait for green APU READY light. |LEFT CONSOLE| 4. Move the ENG CRANK switch to the right to start the right engine. |LEFT CONSOLE| 5. Move the right throttle from OFF to IDLE when the right engine is above 25% rpm (as shown on IFEI). |LSHIFT + HOME|
dugite57 Posted June 12, 2018 Posted June 12, 2018 I had the same issue with the X55. I found the manual is wrong. When you hit Eng Crank, and RPM is 25%+ you need to hit RIGHT SHIFT HOME (not left shift). RIGHT ALT works for the left as stated. Once the engines are running, you'll find your joystick works. I wasted a day trying to configure the throttle. Such is the joy of early release :)
fitness88 Posted June 12, 2018 Author Posted June 12, 2018 (edited) I had the same issue with the X55. I found the manual is wrong. When you hit Eng Crank, and RPM is 25%+ you need to hit RIGHT SHIFT HOME (not left shift). RIGHT ALT works for the left as stated. Once the engines are running, you'll find your joystick works. I wasted a day trying to configure the throttle. Such is the joy of early release :) Thank you! I know the feeling of spending a day working a problem mistake! Edited June 12, 2018 by fitness88
fitness88 Posted June 12, 2018 Author Posted June 12, 2018 BTW, I got all running ok moving the throttles to start with the keys...but I can't get the throttle to move when I move it.
SacredRaziel Posted June 12, 2018 Posted June 12, 2018 You might want to check the controls and verify everything is bound correctly Gesendet von meinem SM-G935F mit Tapatalk
fitness88 Posted June 12, 2018 Author Posted June 12, 2018 You might want to check the controls and verify everything is bound correctly Gesendet von meinem SM-G935F mit Tapatalk Yes it's bound I'll give it another try tomorrow...thanks.
dugite57 Posted June 13, 2018 Posted June 13, 2018 Jump into a mission where the engine is already running, and check if the throttle is working in that situation. Mine was. If it's not working then you'll need to dig deeper...
fitness88 Posted June 13, 2018 Author Posted June 13, 2018 Jump into a mission where the engine is already running, and check if the throttle is working in that situation. Mine was. If it's not working then you'll need to dig deeper... No issue with the throttle works fine...just the issue I mentioned.
Ramstein Posted July 9, 2018 Posted July 9, 2018 I have the same problems with my Saitek and keyboard, the right throttle will not move when starting using keyboard... if I do auto cheat start, it has no problems. left works. ASUS Strix Z790-H, i9-13900, WartHog HOTAS and MFG Crosswind G.Skill 64 GB Ram, 2TB SSD EVGA Nvidia RTX 2080-TI (trying to hang on for a bit longer) 55" Sony OLED TV, Oculus VR
Talonx1 Posted July 11, 2018 Posted July 11, 2018 (edited) Are you saying that even after advancing the individual engine throttles to idle during start procedures that they still wont move after both engines are properly started and running? I had an x52 before before upgrading to an x56 and dont think I had this problem. Are these your procedures... Make sure throttle (x52) is all the way back. Turn on battery Turn on APU, wait for green Move engine crank to Right position, wait for 25% Press (by default) Right shift and Home to advance right engine to idle, wait for engine to stabilize Move engine crank to Left position, wait for 25% Press Right Alt and Home to advance left engine to idle, wait for engine to stabilize Then after both engines are online and stable try moving throttle from lowest position using x52. What throttle axis’ are mapped to the throttle? Edited July 11, 2018 by Talonx1
Recommended Posts