shomke Posted September 2, 2021 Share Posted September 2, 2021 Quick questions dear pilots: 1 - Is the PCM electronic counter measure implemented? And if yes is it really useful? 2 - I'd like to map on my hotas two buttons to increment - decrement the selected CM program, but I could not find the command to do that. Am I blind? Thanks for helping F-16C, M2000C, Persian Gulf Ryzen 5 3600, RX 5700 XT, 32GB ram, Odyssey HMD+, Home-made TrackHat, X56 Hotas. Link to comment Share on other sites More sharing options...
myHelljumper Posted September 2, 2021 Share Posted September 2, 2021 (edited) Hi, For now, PCM always activates the jammer as long as the switch is on the PCM position. It's not how it works IRL, we will work on that once more important subject are done. I'm not on my computer right now, I'll check for the command you are asking for later :). Edited September 2, 2021 by myHelljumper 1 Helljumper - M2000C Guru Helljumper's Youtube https://www.youtube.com/channel/UCK3rTjezLUxPbWHvJJ3W2fA Link to comment Share on other sites More sharing options...
Galinette Posted September 2, 2021 Share Posted September 2, 2021 You might be looking for Decoy Release Program Knob Up / Down in countermeasure category . Link to comment Share on other sites More sharing options...
jojo Posted September 3, 2021 Share Posted September 3, 2021 18 hours ago, shomke said: Quick questions dear pilots: 1 - Is the PCM electronic counter measure implemented? And if yes is it really useful? 2 - I'd like to map on my hotas two buttons to increment - decrement the selected CM program, but I could not find the command to do that. Am I blind? Thanks for helping You have the button on the ECM panel on the right side of the cockpit. Just place it in the middle position. Then you can use the HOTAS button to toggle between PCM and PCR. Currently PCM forces the emission ON. So the HOTAS button will toggle jammer emission ON/ OFF. You don't need to map the ECM panel button on the HOTAS. Mirage fanatic ! I7-7700K/ MSI RTX3080/ RAM 64 Go/ SSD / TM Hornet stick-Virpil WarBRD + Virpil CM3 Throttle + MFG Crosswind + Reverb G2. Flickr gallery: https://www.flickr.com/gp/71068385@N02/728Hbi Link to comment Share on other sites More sharing options...
shomke Posted September 3, 2021 Author Share Posted September 3, 2021 53 minutes ago, jojo said: You have the button on the ECM panel on the right side of the cockpit. Just place it in the middle position. Then you can use the HOTAS button to toggle between PCM and PCR. Currently PCM forces the emission ON. So the HOTAS button will toggle jammer emission ON/ OFF. You don't need to map the ECM panel button on the HOTAS. Thanks Jojo, Yes that's what I do, just place the ECM mode selector in the centre and toogle the jammer on and off. Never used the PCM. I read somewhere the PCM mode is supposed to be a stronger jammer that also mess up your own radar signal, so I was curious to know if it works as intended F-16C, M2000C, Persian Gulf Ryzen 5 3600, RX 5700 XT, 32GB ram, Odyssey HMD+, Home-made TrackHat, X56 Hotas. Link to comment Share on other sites More sharing options...
jojo Posted September 3, 2021 Share Posted September 3, 2021 9 minutes ago, shomke said: I was curious to know if it works as intended As said above, not yet. The ECM panel button is: - VEI. = Veille = stand by (receive only) - middle = HOTAS toggle VEI./ PCM - PCM At the end, we can guess it should be kind like on DCS Hornet. Mirage fanatic ! I7-7700K/ MSI RTX3080/ RAM 64 Go/ SSD / TM Hornet stick-Virpil WarBRD + Virpil CM3 Throttle + MFG Crosswind + Reverb G2. Flickr gallery: https://www.flickr.com/gp/71068385@N02/728Hbi Link to comment Share on other sites More sharing options...
Recommended Posts