gonvise Posted April 11, 2022 Posted April 11, 2022 Two questions about work with JTAC from pilot seat and CPG AI... 1. JTAC give me coordinates of target; I add a TGT point in the TSD. Is possible to view this target point in the IHADSS? I can do a DIR to this target and it appears like a way point, but is there any other way? 2. JTAC laser the target... I'm in PLT seat and with CPG George AI... I order George to change Hellfires to LOAL mode, take the control of the Hellfires selecting them, and shoot orienting the helo to the target... it works and the hellfire hits the target. ¿is this way correct in this momment of implementation or is a better way to fire hellfires to a JTAC lased target (from pilot seat and george AI)? Thanks.
Blackeye Posted April 11, 2022 Posted April 11, 2022 (edited) 14 minutes ago, gonvise said: 1. JTAC give me coordinates of target; I add a TGT point in the TSD. Is possible to view this target point in the IHADSS? I can do a DIR to this target and it appears like a way point, but is there any other way? Set it as acquisition source. Edited April 11, 2022 by Blackeye
GrEaSeLiTeNiN Posted April 14, 2022 Posted April 14, 2022 On 4/12/2022 at 3:23 AM, gonvise said: 2. JTAC laser the target... I'm in PLT seat and with CPG George AI... I order George to change Hellfires to LOAL mode, take the control of the Hellfires selecting them, and shoot orienting the helo to the target... it works and the hellfire hits the target. Is this way correct in this moment of implementation or is a better way to fire hellfires to a JTAC lased target (from pilot seat and george AI)? We only have laser hellfires at the moment and as the pilot cannot lase, I think for now "this is the way" (Mando tone). It should change when we have FCR/radar hellfires. In SP, I normally just fly and fight as CP/G. AMD Ryzen 5 5600X | Gigabyte RTX 3070 Gaming OC 8GB | 64GB G.SKILL TRIDENT Z4 neo DDR4 3600Mhz | Asus B550 TUF Plus Gaming | 2TB Aorus Gen4 TM Warthog HOTAS | TrackIR 5 | Windows 10 Home x64 | My HOTAS Profiles
Kharrn Posted April 16, 2022 Posted April 16, 2022 Am 11.4.2022 um 21:23 schrieb gonvise: Two questions about work with JTAC from pilot seat and CPG AI... 1. JTAC give me coordinates of target; I add a TGT point in the TSD. Is possible to view this target point in the IHADSS? I can do a DIR to this target and it appears like a way point, but is there any other way? 2. JTAC laser the target... I'm in PLT seat and with CPG George AI... I order George to change Hellfires to LOAL mode, take the control of the Hellfires selecting them, and shoot orienting the helo to the target... it works and the hellfire hits the target. ¿is this way correct in this momment of implementation or is a better way to fire hellfires to a JTAC lased target (from pilot seat and george AI)? Thanks. to 1: afaik no, that is the only way to see it in your IHADSS. If you are the Pilot you could have George slave the TADS to that point and see the CPG "cue". to 2: for me most times George does not shoot in LOAL. I have to re-test this though. What i do is that i shoot Hellfires from the Pilot seat. Just do the DIR to the TGT point, be within max range for hellfires, give the JTAC the go to lase and put some "warheads on foreheads" JTAC is even shifting single targets whithin a group when he is ordered (in mission editor) to target a group. Was able to take out 6 artillery vehicles with 6 hellfires in 1 run, with a missile launch every 10sec in LOAL HI. Worked like a charm. Am 14.4.2022 um 03:52 schrieb GrEaSeLiTeNiN: We only have laser hellfires at the moment and as the pilot cannot lase, I think for now "this is the way" (Mando tone). It should change when we have FCR/radar hellfires. In SP, I normally just fly and fight as CP/G. see above (to 2). K
Recommended Posts