Alexrey Posted December 14, 2011 Author Posted December 14, 2011 have try your track Alexrey, i see you have the 2 flags, and no sound of the ILS .. So i have just put a plane on the same airport with the editor for check. As you see no problem there. ( Bar was on stow, so they not appear ) That's very strange, has anyone else had the problems that I'm facing?
Username455 Posted December 14, 2011 Posted December 14, 2011 Yes, happens to me quite often on multiplayer servers when trying to land at senaki. Some maps it works , some it doesnt System: i7 920 @3.8ghz; GTX 560ti 448; 6gb DDR3 1600 ram; 750gb HDD; 750w PSU; Win7 64bit; x52 Pro; TrackIR 5
Lane Posted December 15, 2011 Posted December 15, 2011 Can it be a conflict with mission made before 1.10 and run in 1.10 patched game ? with 1.09 or even lower version. - I7 2600K @5.2ghz ( EK full Nickel waterblock ) - Gigabyte P67A-UD7 B3 - 8GB Predator 2133mhz - 2x HD7970 - EK Nickel EN H2o block - 2x Crucial realSSD C300 Raid0 - Black Widow Ultimate - X52 -TrackIR 5 - XIfi Titanium HD - Win 7 x64Pro
Wichid Posted December 15, 2011 Posted December 15, 2011 Don't think so. I made a quick mission in the editor of fog at batumi and my aircraft a few km away on approach. I played it over and over perfecting ILS approaches with zero visibility. On about 1 out of 10 replays the ILS would not give me any glide slope information. Everything was working fine but it just wouldn't work. I think it may have been an issue that I was outside the glide slope so it was off but I flew over the runway about 100ft too high and had to do a missed approach with the glide slope never activating on ILS. Lyndiman AMD Ryzen 3600 / RTX 2070 Super / 32G Ram / Win10 / TrackIR 5 Pro / Thrustmaster Warthog HOTAS & MFG Crosswind Rudder Pedals
BelgarionNL Posted March 23, 2012 Posted March 23, 2012 still happening in 1.1.1.1 with a friend! I was yelling at him for not being so ****ing stupid! but I guess that was uncalled for! its the ILS
Triangle99 Posted March 23, 2012 Posted March 23, 2012 My ILS is quite hard to fathom. If I enable it on the NMSP, the bars do not appear but if I turn it off on the NMSP the bars do appear (bars are enabled, not stowed and the ILS is powered on and tuned on the right console panel). Plus my ILS flat out will not work at Batumi. P45 Platinum, Q9550 @ 3.33Ghz, HD6970 w/2gb, X-Fi Titanium PCIE, 4gb RAM, ANTEC 1000watt PSU, Lian Li PC-A71 case, Win7 64bit, CH Throttle and Fighterstick, Saitek Pro Pedals, TrackIR 5 + TrackClip Pro, 3 x Samsung SyncMaster 2443
Bearfoot Posted February 8, 2016 Posted February 8, 2016 Resurrecting an old thread, but posting here just in case somebody else is looking for solutions. I had a similar issue: TACAN and ILS freqs correctly set up, navigation set to ILS rather than steerpoint etc., but getting the red bars and neither horizontal nor vertical cues on the ADI. Problem was my ILS was off even though I thought I had switched it on. Reason for this is that ILS "on" and "off" state indicators are, to me, VERY misleading. You see, flipping the ILS switch back and forth, I thought that the white line indicated its current state, so if the white line is pointing to "PWR" it was on. I was mistaken. Turns out the white line pointing to "OFF" means that it is on. I guess the idea is that there are white lines coming out of both OFF and PWR, and switch has a black extension that shows its current state, and this extension blocks part of the white line of "PWR" of it is on and "OFF" if it is off. Confused yet? Well, look at this (GREAT) set of instructions here: http://forums.eagle.ru/showthread.php?t=101213 The image just below "4) Set ILS: Frequency to 110.30 (3) and switch to ON (4, left mouse click)." shows what it looks like with the ILS actually on: solid white line leading to "OFF", and just a stub of line at "PWR". With this the ILS is actually on and functioning. Until I get close to the airport, there is still a red bar on the left side of the ADI and no vertical glide slope cue. But, sure enough, it kicks in eventually.
Recommended Posts