Devrim Posted August 29, 2012 Posted August 29, 2012 Hi... I assigned "zoom" to slider on X52Pro throttle. And this is my curve. However, you see the end of the line (marked by yellow ellipses). When I full push or pull the slider, cockpit camera goes out of my values shown belowzooms. Excessive zoomin in or out. Have anyone got idea how to avoid it? Thanks. Intel i7-14700@5.6GHz | MSI RTX4080 SuperSuprimX | Corsair V. 64GB@6400MHz. | Samsung 1TB 990 PRO SSD (Win10Homex64) Samsung G5 32" + Samsung 18" + 2x8"TFT Displays | TM Warthog Stick w/AVA Base | VPC MongoosT-50CM3 Throttle | TM MFD Cougars | Logitech G13, G230, G510, PZ55 & Farming Sim Panel | TIR5 & M.Quest3 VR >>MY MODS<< | Discord: Devrim#1068
Nate--IRL-- Posted August 29, 2012 Posted August 29, 2012 Try adjusting the saturation? Nate Ka-50 AutoPilot/stabilisation system description and operation by IvanK- Essential Reading
cichlidfan Posted August 29, 2012 Posted August 29, 2012 Yes, as Nate said. Currently your zoom is working exactly like the curve is telling it to. ASUS ROG Maximus VIII Hero, i7-6700K, Noctua NH-D14 Cooler, Crucial 32GB DDR4 2133, Samsung 950 Pro NVMe 256GB, Samsung EVO 250GB & 500GB SSD, 2TB Caviar Black, Zotac GTX 1080 AMP! Extreme 8GB, Corsair HX1000i, Phillips BDM4065UC 40" 4k monitor, VX2258 TouchScreen, TIR 5 w/ProClip, TM Warthog, VKB Gladiator Pro, Saitek X56, et. al., MFG Crosswind Pedals #1199, VolairSim Pit, Rift CV1 :thumbup:
ED Team BIGNEWY Posted August 29, 2012 ED Team Posted August 29, 2012 here is my zoom assigned to a slider, illustration from Peterp zoom in steps, also helps avoid any flickering. Forum rules - DCS Crashing? Try this first - Cleanup and Repair - Discord BIGNEWY#8703 - Youtube - Patch Status Windows 11, NVIDIA MSI RTX 3090, Intel® i9-10900K 3.70GHz, 5.30GHz Turbo, Corsair Hydro Series H150i Pro, 64GB DDR @3200, ASUS ROG Strix Z490-F Gaming, PIMAX Crystal
Devrim Posted August 29, 2012 Author Posted August 29, 2012 (edited) Thanks for fast replies. If I adjust Saturation-Y and raise three or four values at right side, it helps for right ellipse issue, OK. But it doesn't help for left one. (Saturation-X squeezes the graphics from down to up - it's not related with my problem.) EDIT: Hey BIGNEWY; 1) Actually I don't want to see ceiling or bottom of white box. :) This is actually what I want. :) 2) How do you do that your setting without "curves"? - Ah ok, I tried and did it. But as I mentioned above, that's not what I want. Edited August 29, 2012 by Devrim Intel i7-14700@5.6GHz | MSI RTX4080 SuperSuprimX | Corsair V. 64GB@6400MHz. | Samsung 1TB 990 PRO SSD (Win10Homex64) Samsung G5 32" + Samsung 18" + 2x8"TFT Displays | TM Warthog Stick w/AVA Base | VPC MongoosT-50CM3 Throttle | TM MFD Cougars | Logitech G13, G230, G510, PZ55 & Farming Sim Panel | TIR5 & M.Quest3 VR >>MY MODS<< | Discord: Devrim#1068
Nate--IRL-- Posted August 29, 2012 Posted August 29, 2012 See attached. Nate Ka-50 AutoPilot/stabilisation system description and operation by IvanK- Essential Reading
Devrim Posted August 29, 2012 Author Posted August 29, 2012 Thanks. But this is symmetrical (unchecked Slider option). I was trying unsymmetrical. :D I think I can use this though. :) Thanks again Nate. Intel i7-14700@5.6GHz | MSI RTX4080 SuperSuprimX | Corsair V. 64GB@6400MHz. | Samsung 1TB 990 PRO SSD (Win10Homex64) Samsung G5 32" + Samsung 18" + 2x8"TFT Displays | TM Warthog Stick w/AVA Base | VPC MongoosT-50CM3 Throttle | TM MFD Cougars | Logitech G13, G230, G510, PZ55 & Farming Sim Panel | TIR5 & M.Quest3 VR >>MY MODS<< | Discord: Devrim#1068
zacklaws Posted September 1, 2012 Posted September 1, 2012 Does my head in them tuning panels, it would be far easier to be able to type a figure in then trying to move the sliders with a mouse. Every time I feel like fisting the monitor because I cannot get the figure I want as I always seem to go past it, even slowing my mouse down to its lowest DPI setting does not help
Recommended Posts