algerad3 Posted February 15, 2015 Author Share Posted February 15, 2015 Sounds like you missed the export file(Export.lua) . I really need to clean this thread up. The attached file goes into your saved games directory. User/Saved Games/Dcs/Scripts. You might have to create the script file. From what I read, you are capturing the device , just no info. Also, you have to scroll the page wheel after starting sim to get read out. Let me know if this helps.Export.lua [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
algerad3 Posted February 15, 2015 Author Share Posted February 15, 2015 I have been a little sluggish/slow on getting this project going again. Currently drawing ( attempting ) gauges for the 109. Have gauges for the F86 drawn out . Revised some of the steps to get things connected. Just slow going , but going . Hopefully I will have something out by next weekend. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 16, 2015 Share Posted February 16, 2015 (edited) Sounds like you missed the export file(Export.lua) . I really need to clean this thread up. The attached file goes into your saved games directory. User/Saved Games/Dcs/Scripts. You might have to create the script file. From what I read, you are capturing the device , just no info. Also, you have to scroll the page wheel after starting sim to get read out. Let me know if this helps.When I copied the directoutput a10a.lua in scripts, I saw there already was an export.lua file. Is that correct? And if yes, I assume I have to overwrite it? **EDIT** I looked at the export.lua that was already in the dir: nothing in it. So, I copied the above file in the dir. I started the A10 lua file, again: a very quick (dark) cmd window. After that: in DCS, in the A10: my X52 Pro MFD still shows nothing, only "Mode 1" and "No Profile" (and date and time ofcourse, which changes when I use the scroll- or push buttons...) Edited February 16, 2015 by GurbY Link to comment Share on other sites More sharing options...
algerad3 Posted February 16, 2015 Author Share Posted February 16, 2015 (edited) O.k let me check and see what I have going on. I think i screwed the pooch on that one . You should have the export.lua and the Saiteka10c in the script folder. The Directoutput file is the one you need to use to start the connector script. My apologies and I will correct the instructions that you quoted. In the next iteration things will be more simpler. Edited February 16, 2015 by algerad3 clarification and corrections. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 17, 2015 Share Posted February 17, 2015 O.k let me check and see what I have going on. I think i screwed the pooch on that one . You should have the export.lua and the Saiteka10c in the script folder. The Directoutput file is the one you need to use to start the connector script. My apologies and I will correct the instructions that you quoted. In the next iteration things will be more simpler. Ah... NOW something is happening...! I start the d.o. file (screen stays black and does NOT close..?) and start DCS. I choose an A10 hot mission I created. What I see on the MFD is: TENS Power Volume Knob 1, 2, 3, 4 100Mhz pushing the scroll wheels changes the above. That's all that is happening, in the A10C cockpit nothing changes. To be complete: - I have a X52 Pro - I own DCS World A10C Link to comment Share on other sites More sharing options...
algerad3 Posted February 17, 2015 Author Share Posted February 17, 2015 o.k we are getting it sorted. Now when you scroll the right wheel up or down , do the numbers on the mfd change? [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 18, 2015 Share Posted February 18, 2015 o.k we are getting it sorted. Now when you scroll the right wheel up or down , do the numbers on the mfd change? Nope. When I get to lets say 100Mhz, and turn the wheel, nothing happens... Link to comment Share on other sites More sharing options...
algerad3 Posted February 18, 2015 Author Share Posted February 18, 2015 Let me take another look and see what I have. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
algerad3 Posted February 18, 2015 Author Share Posted February 18, 2015 (edited) Gurby , what drivers are you using for the Joy stick? Right now , I am getting nothing to work on mine , the fips work though. I am researching the problem. Also, when your joystick is idle ( no programs activating the screen) what does your mfd screen look like? Edited February 18, 2015 by algerad3 another question. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
algerad3 Posted February 19, 2015 Author Share Posted February 19, 2015 I found myself having issues as well. I used the newer scripts I have created and all the modules would not respond to the scroll wheel. I also checked response in the controller properties page. I found that the scroll wheels were not registering. I uninstalled all of the drivers and reinstalled driver version 6.6.1.40, rebooted and then updated with version 7.0.34.109. Give that a try for starters. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 19, 2015 Share Posted February 19, 2015 (edited) I found myself having issues as well. I used the newer scripts I have created and all the modules would not respond to the scroll wheel. I also checked response in the controller properties page. I found that the scroll wheels were not registering. I uninstalled all of the drivers and reinstalled driver version 6.6.1.40, rebooted and then updated with version 7.0.34.109. Give that a try for starters. OK; I will take a look at that when I'm home. After I received the X52Pro I downloaded the latest drivers from the Saitek website. Could be the directoutput driver..?? When I don't have a profile loaded, the screen says "Mode x" (where x = 1,2 or 3) and "No Profile". Thats it. BTW, I've been searching but can't find the 6.6 driver you mention...? Do you have a link? Edited February 19, 2015 by GurbY Link to comment Share on other sites More sharing options...
algerad3 Posted February 19, 2015 Author Share Posted February 19, 2015 Before you start the process of driver removal, take a look at the joystick property screen and check to see if all of the wheels and buttons register. If not then time to clear up the driver install. when you installed the drivers, did you have the joystick plugged in or did you wait until you were prompted to plug in device to be updated? [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 20, 2015 Share Posted February 20, 2015 Before you start the process of driver removal, take a look at the joystick property screen and check to see if all of the wheels and buttons register. If not then time to clear up the driver install. when you installed the drivers, did you have the joystick plugged in or did you wait until you were prompted to plug in device to be updated? All buttons show response in the joystick control panel: both scrollwheels push and scroll and the middle buttons evenso. I waited till prompted to connect the stick... I did remove the driver and installed "fresh" again (removed everything in registry), still the same.. Link to comment Share on other sites More sharing options...
algerad3 Posted February 20, 2015 Author Share Posted February 20, 2015 Fair enough , I will try something in the morning. Hang tight for a minute. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
algerad3 Posted February 20, 2015 Author Share Posted February 20, 2015 Fixed? Well this has been frustrating. Took me awhile to even get to what you were describing. Then I had to try and track it down but, I think I found it. Try this version of the scripts. If it does not work can you PM me your log file (user/savedgames/dcs/logs/dcs.log)fixed script.zip [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 21, 2015 Share Posted February 21, 2015 Ok, will try and report tomroow! Tnx for all your time, man.....!! Link to comment Share on other sites More sharing options...
algerad3 Posted February 21, 2015 Author Share Posted February 21, 2015 It's all god my friend. This is still a learning experience for me. I do hope to have all things completed this year. And away we go !!! [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
GurbY Posted February 23, 2015 Share Posted February 23, 2015 Well this has been frustrating. Took me awhile to even get to what you were describing. Then I had to try and track it down but, I think I found it. Try this version of the scripts. If it does not work can you PM me your log file (user/savedgames/dcs/logs/dcs.log) I'll send you the log. I tried, but exactly the same results... :( Link to comment Share on other sites More sharing options...
algerad3 Posted March 10, 2015 Author Share Posted March 10, 2015 Just an update to all that is interested. I am still working (refining) on this project. So far , I have created gauges for the the Fw190, Bf109, the F86. Work continues to refine the other gauges as well. The X52 Pro side of the equation is coming along as well. The big news (to me at least) This script does not close when you exit a mission and will resume when you restart a new mission. No more restarting the script while switching or restarting. A revamped guide book will also be included when I complete current goals. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
algerad3 Posted March 14, 2015 Author Share Posted March 14, 2015 For all of you X52 Pro users, what would you find useful to be displayed /controlled on the prop planes? I have not gotten any stick time on any of the modules lately and I am not sure what would be realistically useful. I have gauges completed for the fip's with controls for things as adjusting alt press, fuel gauge test and working on the clock features. just not sure what to do with the X52 other than landing gear lights, flap lights fuel warning ...etc. Hit me and let me know, trying to get the new scripts system out. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
landsraad59 Posted March 15, 2015 Share Posted March 15, 2015 X52 wrapper in C# hi all ! first, excuse me for my english... i'm french may you remember ths issues encountered by Soyo page 21. he got an exception when call : DirectOutputClass.DirectOutput_RegisterDeviceChangeCallback(cb, 0); :helpsmilie:i have the same issue. so i follow your advice: reinstall X52 drivers 6 and 7. but i don't be able to do my wrapper working. is there an opensource wrapper that someone could share ? i work in C#. or is someone could help me to find what's wrong ? big thank in advance Link to comment Share on other sites More sharing options...
algerad3 Posted March 15, 2015 Author Share Posted March 15, 2015 (edited) Landsraad59, I just reread that post and the following post. I believe what happened was that he had two versions of the drivers installed. What you need to do is un install all of the drivers and then dig through you program files and remove anything related to saitek. Go to their download site and get the newest drivers and install. Are you only using the x52 pro or are you also using the fips? Also reference this post. http://forums.eagle.ru/showpost.php?p=1920549&postcount=236 Let me know how it goes. Edited March 15, 2015 by algerad3 adding information [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
algerad3 Posted March 15, 2015 Author Share Posted March 15, 2015 also look at this one for future reference.http://forums.eagle.ru/showpost.php?p=1920549&postcount=236 [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
landsraad59 Posted March 16, 2015 Share Posted March 16, 2015 (edited) X52 wrapper in C# Hi, first thank you for reply. it was my case SD6 and 7 are installed. so i uninstall all. delete all in PFiles and PFfiles (x86). reboot. reinstall x52 drivers v7 only. i have in PFiles (x86) a version of directOutput.dll ( 30/07/2014 18:25 v7.0.34.109) but i was surprised to find again another version in Pfiles ( 30/07/2014 18:58 v7.0.34.109). i download all the drivers from ftp://ftp.saitek.com/pub/software/full/ and i've install Saitek_X52Pro_Flight_Controller_7_0_34_109_64_Drivers_pfw i've read the post about v7.0.11.1 but i cannot download because the link on saitekforum is dead. Can you share the zip again ? thank you Edited March 16, 2015 by landsraad59 Link to comment Share on other sites More sharing options...
algerad3 Posted March 16, 2015 Author Share Posted March 16, 2015 Here is the link to the saitek Drivers. http://www.saitek.com/uk/down/drivers.php Use 7-0-34-109, that is the latest and the one that was working better. [sIGPIC][/sIGPIC] CPIAS FOR Saitek: Saitek Flight instrument panels and X-52 pro mfd scripts for Dcs http://forums.eagle.ru/showthread.php?t=94174 Link to comment Share on other sites More sharing options...
Recommended Posts