SUHANG

thanks for the reply. I tried again this time. It is a in flight condition, without landing gear extended. Still the air break cannot open. My speed is about 600. Is it because of the speed is too hight? What a weird design then if the airbreak extension has an speed limit ?

hi guys, did anyone encounter such problems as the mig29 cannot open the airbreak? no matter on what speed, I press B and there is no any changes. This is really troublesome when I landing. The speed is so high I just bump up on the ground.

Anyone has this problem, the hud display is not centered, as shown in the attached picture. How to fix this? null

Anyone noticed that if you use CBU 99 or MK20 culster bomb, if you launch when the aiming crosser right on the target, the bomb would end up in front of the target. You have to put the crosser behind the target, at least4 times the size of the target then you might hit the target. And this is true either in CCIP or AUTO mode in FA18 what the mechanism of this setting?

nullAs the picture showed. After I landed on the carrier. Then I take off again, the gear became like what the picture showed. And the alarm sound played. At this situation, I cannot fire the missiles. But I can extend the gear and take landing. Is that because I land on the carrier too heavy so the gear doors was broken?

Yes, the historical filter button at the bottom is the problem. I disable it then the walleye appeared. By the way what is this historical filter for ?

Hi Guys, I recently want to use walleye on FA 18, but it doesn't appear on the weapon list for the pylons.Is it an update to delete that weapon? thanks.

This is the mission I edited. Please help me to check what is wrong. thx test JACT.miz

Any one knows why I press F4, it is viewing like this, but not the normal back view? In A10C, FC3, the F4 key shows the back view from the tale, but in FA18, it is like this. wired.

I am pretty sure on following on the right procedures for the JTAC. It's just on the mission editor, when I am creating a JTAC. On the weapon practice mission of FA18, I successfully delivered the laser guided bomb.

Hi guys. does anyone know how to put a JACT in the mission editor？ I want to set up a mission with JACT to designate the target with laser. I tried several times with a ground hammer, but when I contact it, it only report the location of the target but when comes to the laser, it says "no mark". And I tried the drones, it did reply me with the laser mark with the 1688 code. And interact with me when I fly to IP and begin the attack. It even report me "laser on " and the final stage. But when I drop the laser guided bomb, it said abord abord abord, you are not authorized for the attack. I believe I correctly set up the JACT uint with the task execution things, anyone know how exactly to set this JACT things up? thanks

OK, I solved this out. The alignment would not start only after I properly set the emergency parking handle. After I have made the emergency handle vertical and pull it out, which is really set it up properly as the printed beside the handle on the panel, the alignment started, and the FCS bit would be OK. So I just wondering whether in the real world, the FA18 is set like this?

Hi guys, did you encounter this nav alignment problem? Once you landed on the airfield or the carrier, shut down the engine for refueling and rearming, then you cold start up, but the nav alignment just cannot start. The normal procedure is to switch to CV or Ground on the INS Mode Selector. But after I did it, on the HSI, the TIME flashing on 0 and showing NO ATT, simply didn't start the alignment as normal.(as shown in my attachement). The right DDI shows INS ATT, INS DEGO. On the lower DDI, the time flashing on 0:00. And if the alignment is not ok, the GPS weapons can't be used, the HSI position info would not be correct. Anyone has this problem? Plus, after landing, shut down engine and restart, the FCS test can't go well. As shown in the attached pic, the right DDI, FCS first shows intest, than shown restart. Just don't show go.

yes, I deploy the carrier from the add and modify active ship group button. So , I guess it is because I didn't buy the super carrier module.

Hi guys, I noticed there is a Kuznetsov (high resolution) version model in the DCS world latest version. I deployed one and try to put an su 33 on it for start up. But in the mission editor, you simply cannot put the su 33 on it for take off. It can only be put on air. And I tried to fly this on air su33 to land on the Kuznetsov, but every time I just slip over from the deck. The lines cannot be hooked. I am very sure I have the land geer and the hook down. But it is just slipt over the deck. And I contact the carrier for landing, it responding "have not landing permission". So, it is a bug or the Kuznetsov high resolution version model is just a decoration?