Solbaru

Had an issue with Mission 8 last night. Everything worked ok for a while, bombed the mortar then flew back to wapoint 4, at waypoint 4 poodle checked in again and they said continue. Poodle then turned 180 and flew back to around the same point as the mortar was and then just circled it. I stayed until bingo and then flew home but mission wouldn't complete. Will try again tonight to see if its a one off, but a bit strange. Thanks for the campaign tho, enjoying it so far.

Have attached a document that shows the axis tune page for the toe brakes, as mentioned no matter which setting they are always reversed in DCS. Xplane they work fine. toe brakes.zip

Yeah I did rename the input folder and tried and it was the same. The invert check box changes the direction of the X axis but the input from the toe brakes reversed with it. Is the same for every module I own. Not home atm but will post some photos tomorrow. As I said, I can use the rudder pedals in X-Plane and they work perfectly. It is only DCS.

have now tried everything I can think of to fix, short of removing and reinstalling DCS. Unless someone has another option to try??

That's what I'm saying the checkbox is not working. Its odd, checking the invert checkbox reverses the x axis but the input from the toe brakes reverses as well. checked or unchecked the toe brakes are fully on without the toe brakes depressed.

I Have been using these pedals for over a year just fine but this week the toe brakes are working inverted. I have checked the controls configuration and the invert check box is ticked, I have tried every setting to change this but they are always the opposite of what they should be. I have tried a repair, unplugged everything else, re-installed the drivers. I have x-plane 11 on my pc and that still works fine, its just DCS. dcs.log

Im having this issue now as well, I have been using these pedals for a couple of years without issue. Just bought a virpil throttle and now my TFRP pedals have gone to shit. Toe brakes on bot have gone inverted. No matter what I do I can not remove this inversion. Go to the control settings and tick the invert box doesn't change anything. When I look at the output from the VPC tester I can see it inverted but I thought the invert checkbox would solve this. it doesn't. Thru the thristmaster calibration tool everything looks fine. as I said, very strange, this has been working fine for years. I have unplugged everything and uninstalled the thrustmaster software a couple of times. cannot solve this. Anyone have any ideas??? Further investigation, I opened Xplane 11 on my PC and setup the pedals and the invert setting works correctly in the SIM. Looks to be an issue with DCS.

Are there any plans to add the BOL chaff/flare dispenser to DCS? The BOL that is in use on a number of aircraft around the world and has been in use for nearly 20 years would fix the issue of the number of chaff and flares the hornet can carry. each adds 160 chaff/flares to a weapons pylon. Always found the hornet does not have enough. more info https://www.saab.com/newsroom/press-releases/2012/successful-first-flight-for-bol-countermeasures-dispensing-system-on-f-18-in-finland wouldn't have thought it would be that hard to implement in to DCS, not just on the hornet either.

I'm seeing this as well, I use a G2 and had FPS VR running, when it happens it was showing green for the cpu and the vid card, so it doesn't seem to be cpu/gpu heavy load. Was getting 45 -60 fps before but drops to 1 -2 during the slowdown. Only started happening in the last 2 months. Ryzen 9 3900x RTX 2080S 32gb ram M2 pcie 4 drive

I'm using normal. if there is anything I can do to help work out the issue let me know.

I have tried this over 10 times, I let them flypast the crowd before attacking. I have tried everything. I even made myself immortal to try to kill them. they stay immortal no matter what. Hopefully there is a fix soon.

I made some changes last night and I think I have it working, only issue now is, whenever I use a button that uses a "ctrl" key in the combination it stops the whole thing from working. Its like the ctrl key is being held down, which screws everything up. Have to reboot to fix it. might need to email the guy that writes the software for that one..

I have a Thrustmaster Cougar that I have upgraded the throttle with the mmjoy board, I am now trying to get this to work in joystick gremlin as I cant get it to work in TARGET anymore. I am having trouble with the speedbrake switch on the throttle as it needs to be a press and release setting to get it to work correctly. Has anyone done this with Gremlin?? I imagine that the warthog has the same switch process so maybe someone has done it with a warthog on Gremlin... If anyone has this working and doesn't mind sharing the config it would be appreciated..

Im looking at buying the USB upgrade of my cougar that is being offered by MTWsims, does anyone that has completed the upgrade, use the cougar with thrustmaster TARGET?? Just want to check that it works with TARGET before I pull the trigger.

Thanks for that. When I was troubleshooting with AMD they said go back to an earlier driver but 19.7 was as far back as I could find a driver for. Im going to try to find 19.3.1 like you are using and try that. if that works i will be stoked. Thanks for the info.