Dropship Pilot Posted September 16, 2012 Share Posted September 16, 2012 Ah, great stuff! :thumbup: I agree - it won't be the easiest part to cast. Especially if there are threads for the lenses in it. If I had to do it, I'd probably mold it with the lenses already installed and then I'd put two large diameter LEDs into the mold prior to casting. You won't be able to change them, but with LED I don't see a problem there. Nevertheless this will be tricky/and required quite some work. Could you give us the outer diameter and the thickness of the headpiece and the length of the handle. With that info it should be possible to make a convincing replica. Thanks a lot, Stefan Link to comment Share on other sites More sharing options...
Deadman Posted September 16, 2012 Author Share Posted September 16, 2012 (edited) You can see the thread on the Red lens filter in picture three Making the lenses and the black cap would be expensive very time consuming to make. Casting item in the knob would all so invent Murphy to the party. I can see testing a landing gear knob and ship it in working order only for it to be DOA. i would prefer to make some thing that the bulb or LED could be change in. As I have posted in the past I don't usually give out dimensions for items. Edited January 16, 2013 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Dropship Pilot Posted September 17, 2012 Share Posted September 17, 2012 Sorry, I seem to have missed your post(s) about the dimensions. Bad experience in the past? That's ok for me. And thanks again for the great images. Cheers, Stefan Link to comment Share on other sites More sharing options...
Deadman Posted September 17, 2012 Author Share Posted September 17, 2012 Well we will see if there is any more demand for the MFCD I will need to check and see what the minimum order is on the printed circuit boards https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted September 17, 2012 Share Posted September 17, 2012 yes, I need real size MFCD, otherwise, could you tell me the Landing gear Cake dimension? Link to comment Share on other sites More sharing options...
Deadman Posted September 17, 2012 Author Share Posted September 17, 2012 Moken after two post and several pms. I understand you want the MFCD bezels. I am not sure what you mean by cake but I have answered previously no dimension for the landing gear handle or knob yes, I need real size MFCD, otherwise, could you tell me the Landing gear Cake dimension? https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Charles Darwin Posted September 17, 2012 Share Posted September 17, 2012 Deadman, for the gear handle if you cast two separate pieces that would snap together or could be screwed together would that work? you could put red LEDs in the gear handle and if they ever go out just replace them, would also make assembly much easier and if the separation point was hidden in one of the grooves it wouldnt be much of an issue. Link to comment Share on other sites More sharing options...
Deadman Posted September 18, 2012 Author Share Posted September 18, 2012 The amount of time to totally redesign the knob and make a two piece just turned this knob in to a loss. Deadman, for the gear handle if you cast two separate pieces that would snap together or could be screwed together would that work? you could put red LEDs in the gear handle and if they ever go out just replace them, would also make assembly much easier and if the separation point was hidden in one of the grooves it wouldnt be much of an issue. https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted September 22, 2012 Share Posted September 22, 2012 (edited) Thank you DM, and sorry I delay thank you all your reply, Where to buy Landing gear panel's red long button? What name or MIL? My mean the cake is your sory, I need to use your photo for meantion to you Could you give me the cake dimension? Edited September 22, 2012 by moken Link to comment Share on other sites More sharing options...
moken Posted September 22, 2012 Share Posted September 22, 2012 The amount of time to totally redesign the knob and make a two piece just turned this knob in to a loss. Your mean about what? Link to comment Share on other sites More sharing options...
Deadman Posted September 22, 2012 Author Share Posted September 22, 2012 Interesting I would have never guessed you would call a knob cake. This is the landing gear handle knob. I have no idea where you would purchase the red lenses. This is the only placement I have seen this style of red lens there is no marking on the lens or knob to identify the MIL SPEC or NSN Thank you DM, and sorry I delay thank you all your reply, Where to buy Landing gear panel's red long button? What name or MIL? My mean the cake is your sory, I need to use your photo for meantion to you Could you give me the cake dimension? https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Dropship Pilot Posted September 22, 2012 Share Posted September 22, 2012 Judging from this picture... ... I'd say that the lights are (more or less) standard panel lights (in this case with a clear/red cap). The ones on Deadman's landing gear knob have a differend end cap, but seem otherwise identical. The standard lights can be found on ebay under the name "Grimes Post". Cheers, Stefan Link to comment Share on other sites More sharing options...
moken Posted September 22, 2012 Share Posted September 22, 2012 (edited) Hi DM, Thank you for your reply I knew you have real cake XD , could you produce this cake for me? I will try to make lights for this cake and thank you Dropship Edited September 22, 2012 by moken Link to comment Share on other sites More sharing options...
Deadman Posted September 22, 2012 Author Share Posted September 22, 2012 (edited) This means that if I did a complete redesign of the Landing Gear Handel knob making a 3d model. I would need to have some one make a prototype to cast. All are expenses and if only 6 guys purchase the knob it could cost to much per knob to make. The knob is under development once i find a solution that is cost effective it will be for sale. At this time I am progressing with the Main instrument panel, the fire handle housing/ Glare shield, MFCD bezel and the LCD for the MFCD Your mean about what? Edited September 22, 2012 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted September 22, 2012 Share Posted September 22, 2012 This means that if I did a complete redesign of the Landing Gear Handel knob making a 3d model. I would need to have some one make a prototype to cast. All are expenses and if only 6 guys purchase the knob it could cost to much per knob to make. The knob is under development once i find a solution that is cost effective it will be for sale. At this time I am progressing with the Main instrument panel, the fire handle housing/ Glare shield, MFCD bezel and the LCD for the MFCD I also need Main instrument panel, the fire handle housing/ Glare shield, MFCD bezel and the LCD for the MFCD, I will waiting for you, please count me Please tell me how much per 1 unit if you produce Landing Gear Handel knob cake, also please count me Thanks a lot Link to comment Share on other sites More sharing options...
Deadman Posted September 22, 2012 Author Share Posted September 22, 2012 Sorry I don't make cake:smilewink: https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted September 22, 2012 Share Posted September 22, 2012 Hi DM, otherwise, could you tell me each indicator box's dimension? Thank you for your photos for my mention Link to comment Share on other sites More sharing options...
Deadman Posted September 22, 2012 Author Share Posted September 22, 2012 Those are not my pictures https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted September 23, 2012 Share Posted September 23, 2012 Ok, sorry, I knew you have such indicator box, could you give some dimension to me? Thank you DM Link to comment Share on other sites More sharing options...
Deadman Posted September 23, 2012 Author Share Posted September 23, 2012 No all of the indicators i have are currently installed in panels i am not taking apart right now. I don't have time to do that https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted September 24, 2012 Share Posted September 24, 2012 OK, thank you your time Link to comment Share on other sites More sharing options...
doright Posted September 24, 2012 Share Posted September 24, 2012 (edited) I was studying the gear handle photos, what I can't figure out is the electrical pathway used to light the bulbs. It appears that the base of the bulbs contacts the metal ring on the end of the arm, but how is the conductivity established to the other pole? Hand positioned and ready for face palm response to the glaringly obvious I overlooked. Edited September 24, 2012 by doright Link to comment Share on other sites More sharing options...
Deadman Posted September 25, 2012 Author Share Posted September 25, 2012 (edited) There is an outer ring for one pole then insulation and the inner metal ring for the other pole Edited January 16, 2013 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Deadman Posted September 25, 2012 Author Share Posted September 25, 2012 Here is a re post of the Mil spec switches for the left and right consoles Left Counsel The Fuel panel All of the toggle switches are 8500K4 , MS24523-23 http://sensing.honeywell.com/product%20page?pr_id=34134 The line check push button in the upper right hand corner is MS25089-3G http://www.ottoexcellence.com/store/...px?ItemId=3518 The RCVR LT is a Clarostat P009 10 K potentiometer with switch SPST On Off http://www.westfloridacomponents.com...ST+ON+OFF.html The Fill Disable switches are MS-25089-3G-1 ALL valid part alternates - MS25089-3G-1, MIL-PRF-8805/3,MIL-PRF 8805/3, 011023689, 5930011023689 The AUX LTS panel The Indexer and Status lights 2 Clarostat 53C1 SW 10k potentiometer NVIS LTS 2TL1-10A, MS 27408-4A http://sensing.honeywell.com/index.p...tt=MS+27408-4A HARS/SAS 2TL1-3D, MS- 24659-23D http://sensing.honeywell.com/index.php?ci_id=4128&la_id=1&Ntk=si_all_products&N%20=1235&Ntt=MS+24659-23D Signal Lights and lamp test and Fire detect are MS25089-3G http://www.ottoexcellence.com/store/...px?ItemId=3518 The SAS panel 4 each SAS engage switches 25ET61-T http://sensing.honeywell.com/product%20page?pr_id=34972 Monitor test switch 11TW1-7E , MS 27720-27-1E http://sensing.honeywell.com/product%20page?pr_id=32684 The T.O Trim push button in the upper right hand corner is MS25089-3G The Throttle panel 3 each 2TL1-3, MS24524-23 for both fuel flow ,and APU start switches http://sensing.honeywell.com/product%20page?pr_id=35756 2 each 8504K8, MS24659-31N for the Eng Oper MS25089-3G L/G WRN the flap switch will have to wait The LASTE panel EAC switch 25ET61-T information listed above RDR ALTM MS 24659-23D information listed above ENG MS25089-3G information listed above PATH 2TL1-10A, MS2708-4A The Emergency Flight panel EMER RETR MS24659-23F NORM / OVERRIDE MS24525-23 Disengage 2 each MS2708-4A FLAP Emer retard Man rev 8504K6, MS 24659-23D The Intercom panel INT - HM are CLAROSTAT in out switched potentiometers VA388-10K BJ-3 VOL is a Small 10 K potentiometer Rotary Selector Dial. is a 5 position rotary to get the correct angle between stops last unmarked position is used for TACAN audio (Morse ID) Call MS25089-3G The KY-58 panel Zeroing switch MS 27734-23 Delay & on off switches 11TW1-3D Plain, Mode, and Fill COLE F1845-104 9621 http://www.cole-switches.com/Products/index.html The Stall Warning panel 2 Clarostat 53C1 SW 10k potentiometer The Antenna Select panel IFF ANT 1TL1-1E, MS24658-21E UHF UPPER 1TL1-3 , MS24523-23 RADAR BEACON 2TL1-1, MS24524-21 Right Counsel switches Electrical Power Panel APU GEN 8503K36, MS24658-23F INVERTER STAND BY 12TW1-50, MS27753-39 ON ON (ON) TEST IS MOM http://sensing.honeywell.com/product%20page?pr_id=33159 EMER FLOOD 1TL1-3G, MS24658-23G http://sensing.honeywell.com/product%20page?pr_id=34175 AC GEN 2 EACH 11TW1-3, MS27718-23-1 http://sensing.honeywell.com/product%20page?pr_id=32633 BATTERY PWR MS27718-23-1 CMSP Panel JTSN switch MS21026C231 BRT small 10 K potentiometer Systems switches 4x MS27754-5M Mode rotary 42A36-01-05 PULL STOP 1P2 3 4 5 STOP Avionics Auxiliary Panel This one I don't have a panel CDU Power Switch MS21026-E231 8855K8 EGI Power Switch MS21026-E231 8855K8 Page Select Dial 45° indexing angle, 3 or 8 position rotary switch MIL-S-3786 [JANCO Series A, AA, or AC 45° Miniature switch] Or a {COLE 1800, 3900, or 3600 Series Switch, (Example F3645-103)} Steer Point Dial 45° indexing angle, 3 or 8 position rotary switch MIL-S-3786 [JANCO Series A, AA, or AC 45° Miniature switch] Or a {COLE 1800, 3900, or 3600 Series Switch, (Example F3645-103)} Steer Toggle Switch Honeywell Micro Switch 1TL48-7 Environmental Panel OXY TEST IND MS25089-3G WIND SHEILD DEFIG/DEICE MS27718-23-1, 11TW1 3 PITOT HEAT NSN 5930-01-008-6930 PART # A3-1127 TEMP PRESS NORM MS27753-38, 12TW1-10 WINDSHIELD RAIN REMOVE MS27753-39, 12TW1-50 BLEED AIR MS24658-23D, 1TL1-3D MAIN AIR SUPPLY MS24658-23F, 1TL1-3F OPER AUTO MS25128-1, NSN 5930-00-777-5730 CANOPY DEFOG Clarostat 53C1 SW 10k potentiometer FLOW LEVEL Clarostat 53C1 SW 10k potentiometer TEMP LEVEL Clarostat 53C1 SW 10k potentiometer Ext Intr Lights Panel POSITION FLASH MS27753-38, 12TW1-10 FORMATION Clarostat P009 10 K potentiometer wit switch SPST On Offhttp://www.westfloridacomponents.com...ST+ON+OFF.html ANTI-COLLISION 25ET61-T MAGNETICALLY HELD ENG INST Clarostat P009 10 K potentiometer NOSE ILLUM Clarostat P009 10 K potentiometer AUX INST Clarostat P009 10 K potentiometer SIGNAL LTS MS27753-40, 12TW1-70 FLT INST Clarostat P009 10 K potentiometer ACCEL& COMP MS27723-1 12TW1-3 FLOOD Clarostat P009 10 K potentiometer CONSOLE Clarostat P009 10 K potentiometer https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Deadman Posted October 1, 2012 Author Share Posted October 1, 2012 (edited) Air Speed Indicator,AVU-22/A Inside removed Edited January 10, 2013 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Recommended Posts